Battery Installation; Programming The Lock Codes - SentrySafe DH-074E Owner's Manual

Depository Safe
Thank you for purchasing this security safe from Sentry
Getting started
1
Installation of the batteries
(keep door open during setup):
1. Turn the keypad housing counter clockwise
and carefully pull away from the mounting
plate to expose battery compartment.
2. Install four new AAA Alkaline batteries
(factory installed batteries may be included
with some models). Caution: Hold onto the
keypad housing to avoid pulling wires.
Programming your lock codes
2
The SentrySafe electronic lock is shipped with a
factory set master & manager code (see front of
booklet). You should set the lock to your own
unique master & manager code immediately.
Please keep your codes in a secure location.
You may also register your codes on our
website at www.sentrysafe.com.
A single signal (LED flashes and beeps once)
response from the lock indicates valid entry.
A double signal (LED flashes and beeps
twice) response from the lock indicates an
invalid entry.
• If three incorrect entries are entered in a
row, the keypad will shut down for a period
of five minutes. During this shut down period
you will not get a response from the keypad.
Changing the Master Code
(Code length: 1 to 10 digit code) Always
perform this operation with the door open.
1. Enter: # - Existing Master Code - #
2. The set light will stay orange for ten (10)
seconds.
3. Enter: 1 - * - New Master Code - # - New
Master Code - #, before the orange light
disappears.
If a mistake is made during the change, wait
thirty (30) seconds and repeat steps 1 thru 3.
Test the new code several times before closing
the door: Enter: * - Code - #
• The lock will indicate a valid code change
with a single signal.
• The lock will indicate an invalid code change
with a double signal and the old code is still
valid.
Safe. This guide is designed to maximize the user and security features of this product.
®
Note: Do not use rechargeable batteries or any
other type of non-alkaline battery. Do not mix
old and new batteries. Do not mix alkaline and
standard batteries.
3. Carefully position the keypad into the
inserts on the mounting plate and turn
clockwise. Ensure that there are no wires or
cables trapped between the keypad and the
mounting plate. Pinched cables result in a
short circuit.
Changing the Manager Code
(Code length: 1 to 10 digit code) Always
perform this operation with the door open.
1. Enter: # - Master Code or Manager Code - #
2. The set light will stay orange for ten (10)
seconds.
3. Enter: 2 - * - New Manger Code - # - New
Manager Code - #, before the orange light
disappears.
If a mistake is made during the change, wait
thirty (30) seconds and repeat steps 1 thru 3.
Test the new code several times before closing
the door: Enter: * - Code - #
• The lock will indicate a valid code change
with a single signal.
• The lock will indicate an invalid code change
with a double signal and the old code is still
valid.
Activate user codes
(Code length: 1 to 10 digit code) Always
perform this operation with the door open.
1. Enter: # - Master Code or Manager Code - #
2. The set light will stay orange for ten (10)
seconds.
3. Enter: User ID Number (3-7) - * - New User
Code - # - New User Code - #, before the
orange light disappears.
If a mistake is made during the activation, wait
thirty (30) seconds and repeat steps 1 thru 3.
• The lock will indicate a valid code entry with
a single signal.
• The lock will indicate an invalid code entry
with a double signal and the old code is still
valid.
1
4. Enter: * - Master or Manager Code (from
front of booklet) - #
The lock will indicate a valid code entry with
a single signal and the open light will stay
green for five (5) seconds.
5. Turn the handle clockwise before the green
light disappears.
Example: # - Master Code or Manger Code - #
- 5 - * - New User Code - # - New User Code -
#. This will activate User Five (5).
Changing the user code
Always perform this operation with the door
open
1. Enter: # - User Code - #
2. The set light will stay orange for ten (10)
seconds.
3. Enter: New User Code - # - New User Code -
#, before the orange light disappears.
If a mistake is made during the change, wait
thirty (30) seconds and repeat steps 1 thru 3.
Test the new code several times before closing
the door: Enter: * - Code - #
• The lock will indicate a valid code change
with a single signal.
• The lock will indicate an invalid code change
with a double signal and the old code is still
valid.
The Master and Manager can also change
the user codes by following the "Activate user
codes" section steps 1 thru 3.
Deleting user codes
Always perform this operation with the door
open.
1. Enter: # - Master Code or Manager Code - #
2. The set light will stay orange for ten (10) seconds.
3. Enter: User ID Number (3-7) - * - # - #