Related Manuals for Molnar SM300
Summary of Contents for Molnar SM300
- Page 1 T80123— Rev.:30/01-18 3T. Scissor lift Installation instructions (TRANSLATED VERSION) Always keep this document! Must be read before using your equioment!
- Page 2 T80123— Rev.:30/01-18 © Stenhøj A/S Barrit Langgade 188-190 DK-7150 Barrit Tel.: + 45 76 82 13 30 Fax.: + 45 76 82 13 31 E-mail: info@autopstenhoj.com Internet.: www.autopstenhoj.com...
- Page 3 T80123— Rev.:30/01-18 These instructions indicate step by step how you ensure a trouble-free installation and a satisfactory operation. It is there of vital importance that you take the necessary time and care in order to ensure that the installation tole- rances are not exceeded, otherwise the lift will not function effectively and you will not benefit fully from your purchase of the lift.
- Page 4 T80123— Rev.:30/01-18 IMPORTANT: Check that installation site is in accordance with the following points: Indoor and protected against penetrating water. The dimensions of the installation site are as shown on picture 1. Note: The requirements of the local authorities concerning installation of lifts must always be respected. (Rules valid in Scandinavia: distance to walls: min.
- Page 5 T80123— Rev.:30/01-18...
- Page 6 T80123— Rev.:30/01-18 2. Check that all tools shown, or corresponding ones, are available. Provide approx. 9 l hydraulic oil according to specifications in the operation and maintenance instructions. Check that contents of packing are complete, i.e. comprise 2 scissor members, drive-on ramps and locks, a multi-purpose upright, a set of cable rails, a box with accessories and a CD or bag with miscellaneous tech- nical documentation.
- Page 7 T80123— Rev.:30/01-18...
- Page 8 T80123— Rev.:30/01-18 5. Place upright as required – NOTE: should the customer wish to place the upright towards the cable rails some material can be removed from the front cover of the upright. 6. Dismantle front cover and control panel for upright. 7.
- Page 9 T80123— Rev.:30/01-18...
- Page 10 T80123— Rev.:30/01-18 8. Fill in approx. 9 l hydraulic oil. 9. Connection to mains (only to be carried out by authorized electrician) - Wiring diagram is included in control box. - Turn main switch on upright into 0-position before starting installation - Connect according to wiring diagram - IMPORTANT ! Connect to correct voltage –...
- Page 11 T80123— Rev.:30/01-18...
- Page 12 T80123— Rev.:30/01-18 12. Fit cables for photocells in control unit as shown. 13. Fit cables for top and bottom switches in control unit as shown. 14. Push UP-button and by-passing button (see fig. 14) to raise lift to max. height, hereby filling the cylinders with oil and “driving”...
- Page 13 T80123— Rev.:30/01-18...
- Page 14 T80123— Rev.:30/01-18 16. Raise lift to required height. Check distance and perpendicularity between scissor members once again. Note: if floor is not 100% level lift must be shimmed up by means of metal shims, and the whole bottom frame must be supported. In case the lift has to be shimmed up more than 5mm, the bottom plates must be grouted.
- Page 15 T80123— Rev.:30/01-18...
- Page 16 T80123— Rev.:30/01-18 19. Place cable cover plates as required, mark up and drill with ø10x45. Fasten cover plates by means of fischer dowels and bolts supplied. Note ! The distance dimensions must be respected. 20. Check positioning of upright once again. Fasten it to floor by means of expansion bolts supplied.
- Page 17 T80123— Rev.:30/01-18...
- Page 18 T80123— Rev.:30/01-18 21. Raise lift to appropriate working height and fit drive-on ramps. Grease rollers and axles. Note ! Ramps and locks will be marked from factory to ensure correct fitting. Handle for locks has to be fitted at the outer side of lift.
- Page 19 T80123— Rev.:30/01-18...
Need help?
Do you have a question about the SM300 and is the answer not in the manual?
Questions and answers