Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Faulhaber 6501.00088
Summary of Contents for Faulhaber 6501.00088
- Page 1 SC Programming Board 6501.00088 Instruction Manual WE CREATE MOTION...
- Page 2 Faulhaber GmbH & Co. KG. This instruction manual has been prepared with care. Dr. Fritz Faulhaber GmbH & Co. KG cannot ac- cept any liability for any errors in this instruction manual or for the consequences of such errors. Equally, no liability can be accepted for direct or consequential damages resulting from improper use of the equipment.
-
Page 3: Table Of Contents
Content 1 Important Information Symbols used in this instruction manual 2 Install Motion Manager 4 Software Using the USB interface (X9) Using the RS232 interface (X5) 3 Connect the periphery Speed Controller Power supply (X1) 4 Establish Communication 5 Installing the USB Driver System Requirements Setup instructions 6 Additional Information... -
Page 4: Important Information
Please read through the complete instruction manual before using the board. Keep this instruction manual in a safe place for later use. „ FAULHABER is not liable for any data loss, damage or other problems which arise due to use of „ this board. -
Page 5: Install Motion Manager 4 Software
Install Motion Manager 4 Software Install the respective current version of the FAULHABER Motion Manager software onto your PC. It can be downloaded from the FAULHABER internet site: http://www.faulhaber.com/MotionManager Using the USB interface (X9) In order to use the programming board via an USB interface you have to install the appropriate driver in addition, following the installation instruction described in chapter 5. -
Page 6: Connect The Periphery
Connect the periphery Speed Controller Connect your Speed Controller to the fitting terminal or connector: „ „ „ „ Motoranschlüsse 2,54 nsoll LED2 Power LED1 Int. nsoll Ext. LEFT PROG RIGHT Mode nsoll Power supply (X1) Connect the power supply to U and GND (X1). - Page 7 Connect the periphery Power supply (X1) Note Pay attention to the correct position of Jumper JP3 (1-2; U The maximum voltage of U depends on the speed controller. Motoranschlüsse 2,54 It is recommended to use at least 10.5 V as mini- nsoll LED2 mum voltage of U...
-
Page 8: Establish Communication
Establish Communication Open the Motion Manager program and configure the software: 1. Choose the controller type “Speedcontroller without command interface” from the connection wizard and select the COM or USB Port and the baud rate. If the wizard doesn’t appear, click the “help” tab and select “Getting started”. 2. - Page 9 Establish Communication 4. Turn the power supply switch S3 “OFF” and “ON” again. Motoranschlüsse 2,54 nsoll LED2 Power LED1 Int. nsoll Ext. LEFT PROG RIGHT Mode nsoll Now settings and parameters can be configured. The changes are transferred to the Speed Contoller by using the button “Send”. By using the button “Run”...
-
Page 10: Installing The Usb Driver
10 MB hard disk space. „ The “USBX driver for Faulhaber BRC Adapter” is used to operate the programming board via the USB interface. This driver is included in the setup package of FAULHABER Motion Manager Version 4.1 or higher and can be installed from the installation directory after connecting the adapter. - Page 11 Installing the USB Driver Setup instructions Note Pay attention to the correct position of Jumper JP3 (1-2; U The maximum voltage of U depends on the speed controller. Motoranschlüsse 2,54 nsoll LED2 Power LED1 Int. nsoll Ext. LEFT RIGHT PROG Mode nsoll 3) A new hardware will be found;...
- Page 12 Installing the USB Driver Setup instructions 6) The driver will be installed. 7) When the installation is complete, click “Finish”. (The installation may take a few minutes to com- plete.) 8) Now you can use the programming board with Motion Manager.
-
Page 13: Additional Information
Additional Information Speed setpoint input via analog voltage Note This configuration ist standard as delivered condition. The setpoint speed is proportional to the voltage U , which can be adjusted via the potentiometer. nsoll The voltage range of U is defined from 0 – 10 V. The maximum speed value at 10 V can be adjust- nsoll ed via the parameter NsetMax. -
Page 14: Technical Data
Technical Data Operating Data 6501.00088 Power supply for electronics 3,5 … 30 Power supply for motor 0 … 30 Current consumption of electronics Temperature range: – Operating temperature 0 … +65 °C Dimensions and weight: – Dimensions (L × W × H) 80 ×... -
Page 15: Product Layout
Technical Data Product Layout scale reduced Connection information PROG mode No. Function Settings LED 1 Ready for operation S1 PROG LED 2 Status external controller S2 RIGHT Terminals S3 OFF X1 Power supply P1 0V Motoranschlüsse X2, X3, X6, X10 Connector for JP1 Closed 2,54 motor or SC controller... - Page 16 DR. FRITZ FAULHABER GMBH & CO. KG Antriebssysteme Daimlerstraße 23 / 25 71101 Schönaich · Germany Tel. +49(0)7031/638-0 Fax +49(0)7031/638-100 MA05019, English, 1st issue, 04.2009 info@faulhaber.de © DR. FRITZ FAULHABER GMBH & CO. KG Subject to modifications www.faulhaber.com...