Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MK Diamond Products CTS Demolition Cart
Summary of Contents for MK Diamond Products CTS Demolition Cart
- Page 1 CTS DEMOLITION CART OWNER'S MANUAL & OPERATING INSTRUCTIONS Part# 172313 Part# 172313-B Revision 101 08.2018 Manual Part No. 172313-OM Caution: Read all safety and operating instructions before using this equipment. This owners manual MUST accompany the equipment at all times.
- Page 2 INTRODUCTION We at MK Diamond want to congratulate you on selecting the CTS Demolition Cart. We are certain that you will be pleased with your purchase. MK Diamond takes pride in producing the finest prod- ucts in the industry. Operated correctly, your CTS Demolition Cart should provide you with years of quality service. In order to help you, we have included this manual.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SAFETY Page Safety Message/Alert Symbols, Warnings Alert Symbols General, Maintenance, Saw Safety California proposition 65 Message Electrical Requirements and Grounding Instructions 9-11 Safety Label Locations Product Specification OPERATION Blade Installation/Changing Mounting Demo Hammer Installing Scraper Blade Start Up EXPLODED VIEW &... - Page 4 CTS DEMOLITION CART SAFETY Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to you or others. Failure to read and follow these instructions could also result in damage and/or reduced equipment life. Safety warnings and guidelines do not by themselves eliminate danger.
-
Page 5: Alert Symbols
CTS DEMOLITION CART SAFETY PERSONAL PROTECTIVE EQUIPMENT ALWAYS wear approved respiratory, head, ear and eye protection when operating this machine. ACCIDENTAL STARTS! Before starting the engine/motor, be sure the ON/OFF switch is in the OFF position to pre- vent accidental starting. Place the ON/OFF switch in the OFF position before performing any service operation. -
Page 6: General, Maintenance, Saw Safety
CTS DEMOLITION CART SAFETY USE PROPER APPAREL DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that may be caught in moving parts. Non-slip footwear is recommended. Wear protective hair cov- ering to contain long hair. SECURE WORK Clamps or a vise should be used to hold work whenever practical. - Page 7 CTS DEMOLITION CART SAFETY CHECK FOR DAMAGED PARTS Before using a power tool, check for damaged parts. A guard or any other part that is damaged should be carefully checked to determine if it would operate properly and perform its intended function. Always check moving parts for proper alignment or binding.
-
Page 8: Safety
CTS DEMOLITION CART SAFETY SAFETY WARNINGS SILICA DUST WARNING Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. -
Page 9: Electrical Requirements And Grounding Instructions
CTS DEMOLITION CART SAFETY ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS In order to prevent potential electrical shock and injury, the following electrical safety precautions and symbols should be followed at all times! WARNING In case of a malfunction or breakdown, grounding provides a path of least resistance for electric cur- rent to reduce the risk of electric shock. - Page 10 CTS DEMOLITION CART SAFETY ELECTRIC MOTOR SAFETY For maintenance care and operation of the electric motor, refer to your electric motor instruction book- let furnished with the electric motor. Protect the electric motor from dust as much as possible and keep ventilating openings clean.
- Page 11 CTS DEMOLITION CART SAFETY WARNING Use only extension cords that are intended for outdoor use. These extension cords are identified by a marking "Acceptable for use with outdoor appliances; store indoors while not in use." Use only extension cords having an electrical rating not less than the rating of the product.
-
Page 12: Safety Label Locations
CTS DEMOLITION CART SAFETY SAFETY LABEL LOCATIONS Safety labels contain important safety information. Please read the information contained on each safety label. These labels are considered a permanent part of your saw. If a label comes off or becomes hard to read, contact MK Diamond or your dealer for a replacement. -
Page 13: Product Specification
BLADE INSTALLATION PRODUCT SPECIFICATION The CTS Demolition Cart is engineered to hold the Bosch demolition hammer. Its ergonomic design provides the operator with an easier and safer way to demo and prep floors. It offers five blade angles for removal of ceramic tiles, vinyl, sheet vinyl, adhesives and coating from concrete surfaces. -
Page 14: Mounting Demo Hammer
CTS DEMOLITION CART ASSEMBLY MOUNTING DEMO HAMMER Set cart to middle position. Lay cart down and support the Remove face plate. handles to hold the cart level. Place Demo Hammer power Place Demo Hammer on pil- Ensure pillow blocks are cord through hole. -
Page 15: Installing Scraper Blade
CTS DEMOLITION CART ASSEMBLY INSTALLING SCRAPER BLADE Lock shank into place by Place tool retainer lever in Slide shank into tool flipping up tool retainer up position. holder. level. Set cart upright. CAUTION Diamond tools improperly used are dangerous. Comply with American National Standards Institute Safety Code, B7.1 and, Occupational Safety and Health Act covering Speed, Safety Guards, Flanges,... -
Page 16: Start Up
CTS DEMOLITION CART START UP START UP • Ensure Demo Hammer is secure in cart. Plug Demo Hammer into Adjust handle. Adjust cart to desired cart plug. angle. Turn Demo Hammer on. Secure cart with both hands & turn on. - Page 17 NOTES...
- Page 18 CTS DEMOLITION CART EXPLODED VIEW CTS DEMOLITION CART P/N 172313 ITEM NO. DESCRIPTION PART # QTY. WASHER, FLAT, SAE, 3/8 150923 WASHER, LOCK, SPLIT, 3/8 150925 SCREW, PAN HD, #10-24 X 3/8 151097 NUT, HEX, 10-24 151749 CLAMP, CUSHION LOOP 3/8...
- Page 19 CTS DEMOLITION CART PARTS LIST CTS DEMOLITION CART P/N 172313 ITEM NO. DESCRIPTION PART # QTY. COLLAR, SET, 3/4" 153814 COVER, SWITCH 154301 SWITCH, TOGGLE 125V 20A 154310 LABEL, 1-3/4 X 5 MK LOGO 154335 WASHER, FLAT, SAE, #10 154369...
-
Page 20: Exploded View & Parts List
CTS DEMOLITION CART EXPLODED VIEW & PARTS LIST ASSEMBLY TILE SCRAPER P/N 172324 ITEM NO. DESCRIPTION PART # QTY. SCREW, 3/8-16 X 1/4 SOCKET HEAD SET, CUP POINT 162460 SCREW, SOC HD CA, 3/8-16 X 1/2 170114 BLADE, DEMO HAMMER... - Page 21 CTS DEMOLITION CART EXPLODED VIEW & PARTS LIST ASSEMBLY SWITCH P/N 172408 ITEM NO. DESCRIPTION PART # QTY. WASHER, FLAT, SAE, #10 154369 CLAMP, CABLE 154383 SCREW, 8-32 X 3/8 PAN HEAD PHILLIPS 156614 SCREW, PAN HD PHIL MS 10-24X3/4 156641 SPRING, EXT, .30OD X .037WD X 3/4L...
-
Page 22: Ordering Information
ORDERING & RETURN INSTRUCTIONS ORDERING INFORMATION You may order MK Diamond products through your local MK Diamond distributor or, you may order direct from MK Diamond. When ordering direct from MK Diamond, please have the following information ready before calling: •... -
Page 23: Contact
© COPYRIGHT 2018, MK DIAMOND PRODUCTS, INC. ALL RIGHTS RESERVED. The MK Diamond logo is a registered trademark of MK Diamond Products, Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their re- spective owners and used with permission. - Page 24 CTS DEMOLITION CART OWNER'S MANUAL & OPERATING INSTRUCTIONS MK Diamond Products, Inc. 1315 Storm Parkway Torrance, CA 90501 Toll-Free: (800) 421-5830 Phone: (310) 539-5221 Fax: (310) 539-5158 www.mkdiamond.com...