Related Manuals for Alpha Bidet Alpha One
Summary of Contents for Alpha Bidet Alpha One
-
Page 1: Table Of Contents
A L PH A O NE e l ong a ted Components Parts List Pre-Installation Installation Procedure Installation Procedure (cont) Operation Cleaning and Maintenance Self Diagnosis and Specs Warranty Warranty (cont) -
Page 2: Components
ALP H A ON E Components Seat release tab Metal water inlet on the left Control lever Seat T-Valve adaptor Front (bidet) wash (supplied) spray nozzle Rear wash spray nozzle Bidet supply hose (supplied) Water supply hose Shutoff valve... -
Page 3: Parts List
ALP H A ON E Parts List 1.Main body 2. Installation components Metal mounting bolts (2) Butterfly Nut (2) Rubber expansion nuts (2) Plastic mounting bolts (2) Mounting brackets (2) Catch plate Mounting brackets (2) Catch plate Note: There are two methods for installation. The recommended way is using the rubber expansive nuts. The second option is using the butterfly nuts. -
Page 4: Pre-Installation
ALP H A ON E Please make sure you read the instructions carefully and install it properly. Caution 1. The water pressure limit is from 10 to 110 PSI. Please use as instructed. 2. The water shutoff valve should be near where the product is installed. Product Installation Procedure Pre-installation 1. -
Page 5: Installation Procedure
ALP H A ON E Installation Procedure First installation method (recommended) 1. Completely remove the old toilet seat & lid 2. Install expansion nuts. Be sure to firmly press down so the top of the expansion nut is flush with the ceramic toilet surface. Old toilet seat 4.Install the bidet seat 3.Attach the catch plate... - Page 6 ALP H A ON E Connecting Water Supply 2. Unscrew water supply hose from water tank. 1. Close the water supply valve. Flush toilet. Place towel below tank to catch any dripping water. Unscrew to remove 3. Using finger nut, attach T-Valve to water 4.
- Page 7 ALP H A ON E STOP Return the lever to the upright position to turn it off. BIDET (FRONT FEMININE WASH) Gradually push control lever forward until prefered pressure is reached. REAR WASH Gradually push control lever back until prefered pressure is reached.
-
Page 8: Cleaning And Maintenance
ALP H A ON E Cleaning and Maintenance 1. Cleaning the exterior of the bidet seat 2. Cleaning the spray nozzles Use a smooth sponge/cloth with water and/or Pull out the nozzle softly and use a smooth cloth/sponge or soft toothbrush to clean the mild soap to clean the product. -
Page 9: Warranty
ALP H A ON E Self Diagnosis and Troubleshooting Status Cause Solution During use, turn the lever forward or backward to highest setting 1. Low water pressure of the unit Water is too low during WASH/BIDET If the water supply pressure is too low, contact your local water utility. 2. -
Page 10: Warranty (Cont)
ALPHA BIDET at their sole discretion. This limited warranty given by ALPHA BIDET covers all defects encountered in normal use of the ALPHA ONE, and does not apply in the following cases: Loss of or damage to the ALPHA ONE due... - Page 11 ALPHA BIDET, regard less of the possibility and foresee ability of such damages. In no...
Need help?
Do you have a question about the Alpha One and is the answer not in the manual?
Questions and answers
How do you replace the toilet seat Alpha IX Hybrid?
To replace the toilet seat on the Alpha IX Hybrid:
1. Remove the existing toilet seat and lid.
2. Turn off the water supply valve and flush the toilet tank completely.
3. Disconnect the supply hose from the toilet tank.
4. Install the included 7/8″ t-valve onto the tank.
5. Reconnect the water supply hose to the bottom of the t-valve.
6. Place the mounting plate over the bolt holes on the toilet.
7. Insert the two mounting bolts to secure the bracket.
8. Adjust the mounting plate as needed before attaching the bidet seat.
This answer is automatically generated
where in the release button on the alpha one bidet to remove from toilet
The release button is located on the rear right side of the Alpha One bidet.
This answer is automatically generated
Can hydrogen peroxide be used to clean bowl of alpha bidets
No, hydrogen peroxide should not be used to clean Alpha bidets.
This answer is automatically generated
How to I remove the nozzle head to clean it
To clean the nozzle on the Alpha Bidet Alpha One, softly pull out the nozzle and use a smooth cloth, sponge, or a soft toothbrush with water and mild soap. Avoid using harsh chemicals like hydrogen chloride detergent, paint thinner, benzene, abrasive paper, polishing agents, bleach, or chlorine.
This answer is automatically generated
how to install batteries for toilet light