Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Yardbeast 2050RX
Summary of Contents for Yardbeast 2050RX
- Page 1 OWNER’S MANUAL IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit comes equipped with an internal combustion engine and should not www.yardbeast.com, or call (305)- REDERICK METAL INDUSTRIES CO. 1925 NW 21 Terrace. Miami, FL 33142...
- Page 2 Rederick MI Corp. Does not extend any warranty for products sold or exported outside the continental United States; except those sold through authorized Rederick MI Corp. Dealers and/or channels of export distribution. Parts that are not genuine to the Yardbeast Chipper line will not be covered by this or any other warranty expressed by Rederick MI Corp.
-
Page 3: Section 7: Troubleshooting
Having the serial number of your machine at hand, is impo Contact Information: If you require assistance from us: U.S Phone : 305-396-3396 Customer Service e-mail: customer.service@yardbeast.com www.yardbeast.com Note: For repairs beyond the minor ad Engine Information The engine manufacturer is responsible for all engine-... -
Page 4: Section 1: Important Safety Measures
SECTION 1: IMPORTANT SAFETY MEASURES DANGER: After some time, usually clutches and pulleys tend to ‘stick’ to Failure the shaft in a way that you must use other resources other than simply pulling. Best way is to use a claw pulley extractor. If you do not have this tool, or do not know how to use it, you should IMPORTANT: take the machine to a shop and let them do it for you. - Page 5 Changing Belt, Clutch or Engine BEFORE STARTING TO SERVICE YOUR Machine Operation Safety Measures: EQUIPMENT, YOU MUST DISCONNECT THE ENGINE’S SPARK PLUG. FAILURE TO Never DO SO MAY RESULT IN INJURY OR DEATH TO YOU OR OTHERS. any debris and free of pact on foreign objects may result in injury to yourself, or Loosen the bolt in the belt guard, and also loosen up a bolt that is located down below.
- Page 6 SECTION 2: UNPACKING YOUR CHIPPER SHREDDER Loosen the counter knife and place it in between the knife and the rotor’s bore (where products comes out once cut). Tighten Be prepared for arrival: again. This will help you to contain the rotor from rotating when you apply torque to knife’s bolts when loosening and tightening before attempting to operate the equipment: ide these)
-
Page 7: Section 3: Assembling Your Chipper-Shredder
SECTION 3: ASSEMBLING YOUR CHIPPER-SHREDDER Now take apart the side hopper from machine. For this operation you need one (1) 9/16” hex wrench. Loosen bolts Assembling Lateral Chute into Chipper-Shredder: that are fastening the base with the hopper. Watch your hands, try to use mechanic’s glove if available. - Page 8 Regulating Counter knife: You will need to use (2) two 9/16” hex wrench. Loosen side bolts very important, because: that are fastening the front cover against with the cutting chamber fuel lateral covers. You will need two wrenches because bolts tend to slip when torque is applied to the nut and viceversa.
-
Page 9: Section 4: Know Your Chipper Shredder
Section 4: Know Your Chipper Shredder: Sharpening or replacing chipping blades: Deflector: clearly two different ways of operation, or of the product by placing its location pin on For sharpening or replacing blades you will need to better said, two different applications, that take off both front-cover and side hopper. -
Page 10: Section 5: Operating Your Chipper Shredder
Section 5: Operating your Chipper Shredder WARNING: The operation of any chipper shredder can result in foreign objects being thrown into the eyes, which can damage eyes severely. Always wear safety glasses and protective wear while operating or repairing this machine. Gas and Oil Fill Up: Starting the Engine: - Engines with primer:...
Need help?
Do you have a question about the 2050RX and is the answer not in the manual?
Questions and answers