Advertisement
Advertisement
Table of Contents
Related Manuals for Behringer EUROPORT PPA2000BT
Summary of Contents for Behringer EUROPORT PPA2000BT
- Page 2 Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure - voltage that may be sufficient to constitute a risk of shock This symbol, wherever it appears, alerts you to important operating and maintenance...
-
Page 3: Legal Disclaimer
16 Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. LEGAL DISCLAIMER TECHNICAL SPECIFICATIONS AND APPEARANCES ARE SUBJECT TO CHANGE WITHOUT NOTICE AND ACCURACY IS NOT GUARANTEED. BEHRINGER, KLARK TEKNIK, MIDAS, BUGERA, AND TURBOSOUND ARE PART OF THE MUSIC GROUP (MUSIC-GROUP.COM). ALL TRADEMARKS... -
Page 4: Limited Warranty
WHICH MAY BE SUFFERED BY ANY PERSON WHO RELIES EITHER WHOLLY OR IN PART UPON ANY DESCRIPTION, PHOTOGRAPH OR STATEMENT CONTAINED HEREIN. COLORS AND SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT. MUSIC GROUP PRODUCTS ARE SOLD THROUGH AUTHORIZED FULLFILLERS AND RESELLERS ONLY. - Page 5 EUROPORT PPA2000BT/PPA500BT Set-up Step 1: Hook-Up Debate Centre de débat Podiumsdiskussion...
- Page 7 Step 2: Set-up 1,Release the top latch beneath the carrying handle 2,Release the side latches by pressing and then lifting them. 3,Remove the speakers and place them in appropriate locations.
- Page 8 4,Stand the mixer upright.(Make sure the include speaker cables can reach both speakers)
-
Page 9: Effects Processor
Step 3: Controls. EQ KNOBS adjust the high and low knob determines how much of each frequencies for each channel. channel’s signal goes to the DIGITAL EFFECTS PROCESSOR. - Page 10 PAN knob positions LEVEL knob adjusts the CLIP LED lights when the each channel in the volume of the individual input signals overloads the stereo field. channel in the overall mix. channel. MULTI-FX PROCESSOR unit adds a selected sound effect to any channels which have their PROGRAM[PUSH] EFFECTS...
- Page 11 GRAPHIC button button MAIN LEVEL CONTROL adjusts specific activates activates the FBQ adjusts the overall volume of frequencies in the GRAPHIC EQ. detection system. the main mix. The MODE sound spectrum. The EQ IN button switch selects stereo or mono must also operation.
- Page 12 DIGITAL WEIRELESS USB MIC INPUT PHANTOM button BLUETOOTH PATRING input accepts optional jacks accept button and indicator connect sends BEHRINGER wireless dynamic(hand phantom power to your Bluetooth device. microphone receiver. The LEDs held)or power condenser indicate wireless microphone condenser microphones.
-
Page 13: Speaker Outputs
jacks STEREO AUX IN RECORDING OUT inputs route stereo send the main mix signal out to signals directly into the an external recording device or main mix through either another mixer. a signal’s 1/8’’ TRS stereo plug or left and right 1/4’’plugs. - Page 14 POWER switch turns the power to the unit on and off POWER SOURCE accepts the included IEC power cable into this jack. Step 4: Getting started...
- Page 15 1,Connect the included speaker cables to the speakers and to the rear SPEAKER OUTPUTS on the mixer. Make all the appropriate audio connections to the mixer. Power down all external devices. 3, Set all the channel controls as shown (TREBLE, BASS, and BAL centered; EFFECTS and LEVEL down/off).
- Page 16 6,Power up all external devices. Power up the PPA2000BT/PPA500BT by pressing the POWER button. 8,If you are using BEHRINGER wireless microphones, plug the wireless dongle into the DIGITAL WIRELESS USB input, The DIGITAL WIRELESS LEDs will light up when the wireless microphones become active.
- Page 17 11, If a channel’s CLIP LED lights, press the PAD button. If the PAD button is already engaged, turn the LEVEL knob down. Always use the pad button with line level inputs. Adjust the left-right position of a channel in the stereo field by turning the channel’s PAN knob.
- Page 18 13, Make final volume adjustments using the MAIN LEVEL CONTROL knobs.
-
Page 19: Step 5: Adding Effects
Step 5: Adding Effects 1,Set the FX [LEVEL] knob on the DIGITAL EFFECTS PROCESSOR to approximately a 75% setting. Scroll through the available effects by turning the PROGRAM [PUSH] knob. The number in the display will flash. Press the PROGRAM [PUSH] knob to select the effect. The number will stop flashing. While speaking, singing, or playing, turn the channel FX knob up to the desired level on each channel to which you wish to add effects. - Page 20 Adjust the FX [LEVEL] knob on the from DIGITAL EFFECTS PROCESSOR up or down the initial 75% setting to achieve your desired overall effects level in the main mix. Step 6: Feedback Detection “Feedback” is the undesirable high-pitched sound created by sound waves looping between the speakers and the microphones.
- Page 21 feeding back. Lower the lit EQ slider until feedback stops.
-
Page 22: Specifications
Specifications INPUTS 1-4 Type 4xXLR,electronically balanced 4x1/4’’TRS jack, electronically balanced Impedance Approx2.2 kohm, balanced Approx 1.1 kohm, unbalanced Input -21 dBu @PAD/OFF Max.gain +30dB to +10dB Phantom power supply +48V Signal-to-noise ratio -90dB, A-weighted Channel separation 70dB INPUTS 5-8 Type 4x1/4’’TS jack, unbalanced 4xRCA jack, unbalanced Impedance... - Page 23 BASS ±15dB @80Hz TREBLE ±15dB @12kHz EFFECTS Converter 24-bit delta-sigma Sampling frequency 40kHz Display 2-digit, 7-segment Type 7-band LOUDSPEAKER OUTPUTS Type 2x1/4’’ TS jack Load impedance 8ohm OUTPUT POWER RMS(@8ohm) 2x160 Watts RMS(@4ohm) 2x300 Watts PEAK power(@8ohm) 2x500 Watts PEAK power(@4ohm) 2x1000 Watts SYSTEM SPECIFICATIONS Frequency response...
- Page 24 BLUETOOTH Frequency Range 2402~2480 MHz Channel Number Version Bluetooth spec V2.1+EDR compliant Output power 4dBm Modulation Type GFSK ,π/4- DQPSK, 8DPSK Date Rate 3 Mb/s...
- Page 25 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.