Advertisement
Resolving Technical Problems
Please consult the following table BEFORE contacting your dealer or local SAMSUNG
representative.
Problem
The software installation failed
Check that your hard disk is not full.
The installation floppy disk may be corrupted.
Repeat the installation with the backup floppy disk.
I re-booted my PC and it paused
After installing the device driver, your system
during the start-up program.
start-up program may take more time than
expected. If it does not start-up after 60 seconds,
verify your AUTOEXEC. BAT file and, if
necessary, contact your local computer dealer.
The disc tray does not open.
The drive may not be installed correctly. Verify the
physical installation.
In the File Manager, the CD-ROM
If you have installed the
CD-ROM drive ...
icon does not display.
And the software
And have not installed
the software
I installed the software and re-
When the program of Windows 95/98 is broken up, re-stall
it as the computer can not read the program anymore.
booted my PC. The CD-ROM
drive icon/directory still does not
Verify the connections between the drive and your PC.
appear.
Check that the 40-pin flat cable is connected to an IDE
interface (some PCs are equipped with an SCSI disk
interface).
Verify your AUTOEXEC. BAT file. Go to page 5 for
the verification procedure.
Check the LASTDRIVE = command in the CONFIG. SYS
file. The specified letter must take the CD-ROM volume
into account. If you do not know which letter is assigned
to the CD-ROM, enter Z.
Using the documentation provided with your PC, check
that the IDE hard disk is set up in MASTER mode.
Meaning / Solution
Then ...
Re-boot your PC.
Install the software
following the instructions
on page 5.
6
Technical Specifications
SAMSUNG continually strives to improve its products. Both the design
specifications and these user instructions are thus subject to change without
notice.
SECTIONS
CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1,
Disc types supported
Form-2, CD-Plus, CD-Extra, Photo-CD(Single, Multi-session),
DISC
Video CD ready, Enhanced CD, CD-I/FMV, CD-R
Disc diameter
Data transfer rate
PIO Mode - 4. DMA MW2
Access time (1/3 stroke)
Data buffer capacity
128KB
DRIVE PER -
FORMANCE
Laser
Semiconductor Laser
Slide mechanism
Gear motor
Spindle motor
Brushless motor
Loading type
Tray Loading, DC motor(Soft Eject)
ERROR RATE
Mode-1 : 1block / 10 bits, Mode-2 : 1 block/10 bits
Button
Open/Close
Indicator(LED)
Busy
FRONT PANEL
Headphone output
Stereo Mini - jack (¯ 3,6 mm) 0.60 ± 20% (Vrms) 33½
Volume control
Dial type
Required power
+5V DC 1.7A,
+12V DC 1.0A
REAR PANEL
ATAPI
Interface connector
Audio output
Line out 0.70 ± 20%(Vrms), 47k½
Jumper block
Device configuration jumper
Work area
OPERATING
Temperature : 5~45 ¡C, Humidity : 8~80%
ENVIRONMENT
Temperature : -40~60 ¡C, Humidity : 5~90%
Storage area
Dimensions
149(W) x 42.5(H) x 200(D)mm
GENERAL
(Including bezel)
Net weight
950g
MTBF
125,000 POH(Duty 20%)
RELIABILITY
Disc compartment loading
30,000 times
SC-140
SC-148
12cm or 8cm
Max. 6000KB/s
Max. 7200KB/s
80ms(typical)
70ms(typical)
12
9
7
Advertisement
