Related Manuals for Akrapovic S-H10R6L-TC
Summary of Contents for Akrapovic S-H10R6L-TC
- Page 1 Installation instructions RACING & EVOLUTION Honda CBR 1000RR (08-09), Honda CBR 1000RR ABS 2009 *502262* www.akrapovic.com...
- Page 2 1. The manufacturer, importer or dealer shall not be liable for any incidental damage including personal injury or any other damages caused by improper installation or operation of the rapo i e haust system.
- Page 3 Apply 3 to 4 small drops of bolt sealant onto the cleaned and degreased threads before tightening the bolts. voi co tact with ki m co m m ra o ot i ha p o t o r ach o chi r blac tube rovides trouble-free and long-lasting protection against sei ing, corrosion and rusting of bolts, threaded ends, nuts, joints, etc.
- Page 4 . Disconnect and remove the e haust valve cable and than reattach the plastic servo motor s cover onto original position r 2 .
- Page 5 nscre the bolt from the muf er chassis hanging brac et . nscre the bolts from the left lo er part of the co ling...
- Page 6 5 6 .
- Page 7 nscre the bolt from the metal clamp at the muf er - lin pipe joint and remove the muf er...
- Page 8 ling...
- Page 9 emove the lo er part of the co ling then unscre the bolts and remove the plastic fasteners from the left and right side of the co ling 20 .
- Page 10 www.akrapovic.com...
- Page 12 www.akrapovic.com...
- Page 13 r 20...
- Page 14 Disconnect the vacuum pipes and turn signals electrical connectors 22 . r 22...
- Page 15 nscre the bolt from the lo er ater cooler hanging brac et and slightly remove the cooler r 2 . : o ot i co ct th coo i t m t nscre the bolts from the header tube anges r 2 .
- Page 16 25 and remove the stock header tubes r 26 . r 25 r 26...
- Page 17 et up the sleeves together ith the anges and springs. ake sure they are correctly oriented and that the holes for attaching the springs line up ith the loops on the header tubes. Do not tighten up the anges : mak ot to ama th coo i...
- Page 18 : coat the interior side of the input bushes of the titanium collectors ith Akrapovic ceramic anti-sei ing grease hite tube . Insert the header tubes properly, attach the springs and tighten the anges make sure not to damage the cooling 0 .
- Page 19 2 . or vo tio : coat the interior side of the input bushes of the titanium link pipe ith Akrapovic ceramic anti-sei ing grease hite tube . : mak that...
- Page 20 Tighten the lambda sensor. ake sure not to damage the sensor s electrical lead . i the lambda sen- sor electrical lead ith plastic tie onto the plastic bracket and cut a ay e cess of the tie 29 Nm...
- Page 21 emove the rubber dampers and the metal collar from the muf er bracket 5 . Remove the footrest and put the 5 mm aluminium distance bushes under the footrest than reattach the footrest ith the stock bolts 25 Nm 18 ftlb...
- Page 22 Insert the aluminium bush to the muf er bracket orrectly position the carbon- ber clamp and slide it onto the muf er - bear in mind the t of the carbon- ber clamp vie ed from the rear : op...
- Page 23 : coat the interior side of the input bush of the muf er ith Akrapovic ceramic anti- sei ing grease hite tube .
- Page 24 Tighten the bolts on the carbon- ber clamp and clamp to stock muf er bracket joint ake sure the link pipe or muf er are not touching the frame, s ing arm or any other part of the motorcycle. Attach the co lings in the...
- Page 25 i a i ta atio : lean grease spots uf er carbon- ber outer sleeve use a soft dry cloth. uf er titanium outer sleeve use a soft cloth sprayed ith a multi-purpose spray lubricant D-40 or e uivalent . uf er carbon- ber outlet cap use a soft dry cloth.
- Page 26 HONDA CBR 1000RR (WITHOUT ABS)/ Racing line, Model year: 2008 - 2009 Product code: S-H10R6L-TC S-H10R6L-TT P-82 INNER SLEEVE P-F40 FLANGE V-TUV003/1 NOISE REDUCTION INSERT H-H10R6 HEADER SET V-EC28 END CAP SET FOR TITANIUM OUTER SLEEVE MUFFLER V-EC35 END CAP SET FOR CARBON FIBRE OUTER SLEEVE MUFFLER...
- Page 27 HONDA CBR 1000RR (WITHOUT ABS/ )Complete exhaust system/Racing line tube set with street legal Slip-on muffler, model year 2008-2009 Product code: S-H10R6L-TC/1 WARNING! IN CASE OF COMBINATION WITH RACING TUBE SET, THE SLIP-ON HOMOLOGATION IS NOT VALID! S-H10R6L-TT/1 M-HT00805T/1 FULL TITANIUM MUFFLER...
- Page 28 HONDA CBR 1000RR ABS/ Complete exhaust system/ RACING LINE, Model year: 2009 Product code: S-H10R7-TT S-H10R7-TC (P-82) INNER SLEEVE (P-F40) FLANGE (V-TUV003/1) NOISE REDUCTION INSERT (H-H10R7) HEADER SET (V-EC28) END CAP SET FOR TITANIUM OUTER SLEEVE MUFFLER (V-EC35) END CAP SET FOR CARBON FIBER OUTER SLEEVE MUFFLER...
- Page 29 HONDA CBR 1000RR ABS/ COMPLETE EXHAUST SYSTEM/ Racing line tube set with street legal Slip-on muffler, Model year 2009 Product code: S-H10R7-TT/1 WARNING! IN CASE OF COMBINATION WITH RACING TUBE SET, THE SLIP-ON HOMOLOGATION IS NOT VALID! S-H10R7-TC/1 (P-82) INNER SLEEVE (P-F40) FLANGE (V-TUV003/1) NOISE REDUCTION INSERT (H-H10R7) HEADER TUBE SET...
- Page 30 www.akrapovic.com...
Need help?
Do you have a question about the S-H10R6L-TC and is the answer not in the manual?
Questions and answers