Advertisement
Quick Links
Installation Instructions for Mincey Marble Manufacturing's
For use with the Confetti Tile Pattern Contemporary Panel System
DISCLAIMER NOTICE: If the prescribed method of installation is not followed
precisely, the foot rest may detach from the wall and cause damage to the panels
and the walls. If the foot rest ledge detaches, physical injury to the occupant of
the shower may occur. Mincey Marble will not be liable for any damages to
persons or property because of incorrect installation.
These instructions have been written for Mincey Marble's FR-03 cast marble wall
mount foot rest ledge. If you have a different product than shown, please call us
Wall Mount Foot Rest Ledge
- FairField Inn & Suites by Marriott -
Product number: FR-03
for instructions for the product you received.
Mincey Marble Mfg., Inc.
4321 Browns Bridge Road
Gainesville, GA 30504
Ph: 800.533.1806
Fx: 770.531.0935
www.minceymarble.com
1
Advertisement
Related Manuals for Mincey Marble Manufacturing FR-03
Summary of Contents for Mincey Marble Manufacturing FR-03
- Page 1 Mincey Marble will not be liable for any damages to persons or property because of incorrect installation. These instructions have been written for Mincey Marble’s FR-03 cast marble wall mount foot rest ledge. If you have a different product than shown, please call us...
- Page 2 FR-03 Section I Section I provides necessary details for installing the FR-03 foot rest ledge into an area that includes wood blocking. In preparation, before installing this foot rest ledge, you will need to have completed the installation of the panel systems and sealed the seams of the shower panels behind where the foot rest ledge is to be installed with 100% silicone.
- Page 3 DISCLAIMER NOTICE: If the prescribed method of installation is not followed precisely, the foot rest ledge may detach from the wall and cause damage to the panels and the walls. If the foot rest ledge detaches, physical injury to the occupant of the shower may occur.
- Page 4 2. Using a corded drill and a 3/16” masonry drill bit, pre-drill the cast marble panels, being careful to avoid drilling into the wood blocking. 3. Drive the # 10 Stainless Steel Truss Head Screws (see illustration 3) into the wood blocking, being sure to keep the screws level with each other and perpendicular to the cast marble shower panels.
- Page 5 6. Using a # 2 Phillips head screwdriver, tighten the truss head screws as tightly as possible. You will hear creaking noises when the screw is tight against the support of the foot rest ledge. A right-angle screwdriver will make it easier to turn the screws. A ratcheting right-angle screw driver is optimal for this installation.
- Page 6 Section II Section II provides all of the necessary information for installing the FR-03 foot rest ledge into an area that does not provide wood blocking. DISCLAIMER NOTICE: If the prescribed method of installation is not followed precisely, the foot rest ledge may detach from the wall and cause damage to the panels and the walls.
- Page 7 8. # 2 Phillips Head Screwdriver to tighten screws when attaching foot rest ledge (A right- angle or ratcheting right-angle screwdriver will make the installation easier) Either a WingIt Apache 200 Drill Bit, Part # WA200Gt34 (which may be purchased from Mincey Marble), or a ¾”...
- Page 8 A ¾” hole must be drilled into the surround panel and through the substrate in order to use the MAW35-SD Master WingIt. These holes need to be drilled precisely in order to maintain alignment of the top of the foot rest ledge with the 1½” solid band. 4.
- Page 9 9. Once the truss head screws have been tightened, try to move the foot rest ledge by applying pressure with your hands to the foot rest ledge. If there is any movement, re- tighten the screws until movement stops. 10. Apply color matching silicone around the perimeter of the foot rest ledge to seal the foot rest ledge to the cast marble panels.
Need help?
Do you have a question about the FR-03 and is the answer not in the manual?
Questions and answers