Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
MP7ER/FR Remote
Double Inverted Magnetron
Cold Cathode Gauge
Range: 7ER 10-8 to 10-2 Torr
7FR 10-11 to 10-2 Torr
TELEVAC
THE FREDERICKS COMPANY
A DIVISION OF
2400 PHILMONT AVE.
HUNTINGDON VALLEY, PA 19006
phone: (215) 947-2500
fax: (215) 947-7464
e-mail: sales@televac.com
web site: www.televac.com
9/11
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TELEVAC MP7ER
Summary of Contents for TELEVAC MP7ER
- Page 1 INSTRUCTION MANUAL MP7ER/FR Remote Double Inverted Magnetron Cold Cathode Gauge Range: 7ER 10-8 to 10-2 Torr 7FR 10-11 to 10-2 Torr TELEVAC THE FREDERICKS COMPANY A DIVISION OF 2400 PHILMONT AVE. HUNTINGDON VALLEY, PA 19006 phone: (215) 947-2500 fax: (215) 947-7464 e-mail: sales@televac.com...
- Page 2 PARTS LIST ITEM DESCRIPTION 7ER/FR Remote Cold Cathode Electronics Cable (specified at ordering) Instruction Manual Sensor phone: (215) 947-2500 fax: (215) 947-7464 e-mail: sales@televac.com web site: www.televac.com 9/11...
-
Page 3: Table Of Contents
CALIBRATION ……………………………………………………………………………… .9 TROUBLESHOOTING …………………………………………………………………….…9 SPECIFICATIONS …………………………………………………………………………..10 DIMENSIONS ………………………………………………………………………………..11 UNPACKING AND INSPECTION ………………………………………………………….12 WARRANTY INFORMATION ………………………………………………………………12 PLEASE READ THIS MANUAL THOROUGHLY BEFORE USING GAUGE. REPORT ANY PROBLEMS IMMEDIATELY. phone: (215) 947-2500 fax: (215) 947-7464 e-mail: sales@televac.com web site: www.televac.com 9/11... -
Page 4: Description And Instrument Operation
PLC, chart recorder, or data acquisition system. The MP7ER/FR series of instruments use the time proven reliable and rugged TELEVAC 7ER/FR Sensor, which can be changed in seconds. These instruments operate from low voltage DC and are easily integrated into the largest process system with a minimal effort. -
Page 5: Safety
- personal safety, property damage or danger from electrical shock. Read these instructions carefully. In these instructions the word “product” refers to the MP7ER/FR and all of its approved parts and accessories. NOTE: These instructions do not and cannot provide for every contingency that may arise in connection with the installation, operation, or maintenance of this product. -
Page 6: Principles Of Sensor Operation
Because of the danger on introducing additional hazards, do not install substitute parts or perform any unauthorized modifications to the product. Return the product to Televac for service and repair to ensure that safety features are maintained. Do not use this product if it has unauthorized modifications. -
Page 7: Sensor Operation And Sensor Installation
The new value is retained in memory and the corresponding new voltage is provided at the setpoint terminal on the connector and is scaled in the same way as the signal output. phone: (215) 947-2500 fax: (215) 947-7464 e-mail: sales@televac.com web site: www.televac.com 9/11... - Page 8 Relay Normally Open SIG Ground Relay Common Setpoint output Display Setpoint R E M O T E D IG IT A L Adjust Setpoint Setpoint Relay on LED display phone: (215) 947-2500 fax: (215) 947-7464 e-mail: sales@televac.com web site: www.televac.com 9/11...
-
Page 9: Recorder Outputs
1 .0 0 E - 0 3 1 .0 0 E - 0 2 P R E S S U R E ( T O R R ) phone: (215) 947-2500 fax: (215) 947-7464 e-mail: sales@televac.com web site: www.televac.com 9/11... -
Page 10: Maintenance
Install “O” ring in body.. 2.10 Replace the anode assembly in the body after the “O” ring has been installed. 2.11 Screw the cap on and hand tighten. phone: (215) 947-2500 fax: (215) 947-7464 e-mail: sales@televac.com web site: www.televac.com 9/11... -
Page 11: Calibration
6, paragraph 2.0 of this manual. NOTE: If, after doing some or all of the above, the unit is still inoperative, return to the factory for repair. phone: (215) 947-2500 fax: (215) 947-7464 e-mail: sales@televac.com web site: www.televac.com 9/11... -
Page 12: Specifications
Adjustment Potentiometer Form C Contact Setpoint Operating Temperature Calibration Medium + 15 to 50C Dry Air or Nitrogen Sensor Material Overpressure Tolerance Stainless Steel (Type 304) 150 PSI phone: (215) 947-2500 fax: (215) 947-7464 e-mail: sales@televac.com web site: www.televac.com 9/11... -
Page 13: Dimensions
CHAPTER 10 TELEVAC Dimensions phone: (215) 947-2500 fax: (215) 947-7464 e-mail: sales@televac.com web site: www.televac.com 9/11... -
Page 14: Unpacking And Inspection
CHAPTER 12 Warranty information The Televac division warrants instruments and components to be free of defects in material and workmanship for a period of one year after the date of shipment unless otherwise specified in the quotation pr product literature. No salesman, Representative or agent of the Fredericks Company, or its divisions is authorized to give any guarantee or warranty or make any representation in addition or contrary to those stated herein.
Need help?
Do you have a question about the MP7ER and is the answer not in the manual?
Questions and answers