Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for GeoBox G-403
Summary of Contents for GeoBox G-403
- Page 1 G-403-3 G-403 Quick User Manual (4 screens irregular video wall controller) Technical support: E-mail: sales@vnstw.com Tel: +886-2-8751-2785 ext. 301 Cell: +886-935-678-033 Skype: vns-inc Version: 2.08 Website: www.vnstw.com.tw...
-
Page 2: Table Of Contents
How to key-in coordinates.………………………………………........7.3.1 Load coordinates via remote controller…………………......... 7.3.2 Load coordinates via [GAlign] PC tool..............Video wall with multiple units of G-403..................Case study A (Full HD signal source)....…………………………………………… Case study B (4K signal source)..................Case study C (Video wall with 15x 55” LCD).............. -
Page 3: Introduction
PC tool. G-403 is 4 screen video wall controller with PIP/POP function and supports up to 4k/2k 30hz input. 4K/2k loop out port is available for daisy chain connection. It can be cascaded to create large scale video wall. - Page 4 15. Auto power on/off control: When no input signal is detected, GeoBox can auto-turn off output signal. Once input signal is detected, it will auto-turn on GeoBox and send out signal again. It is convenient for system power on/off control.
-
Page 5: Outlook And Main Functions
G-403-3 Outlook and main functions Note: After finishing DIP SW setting, Power OFF and ON again is required to execute the settings. How to use IR remote controller Output port selection (TV1-TV4) Store location for manual setting display modes (IDX1-IDX10) Procedures for determine each LCD position 1. -
Page 6: How To Use Preset Display Mode
User can use more advanced functions by OSD menu through remote controller or GAlign PC tool. b、 If GeoBox is installed at a location that can‟t be directly accessed by remote controller, please connect IR Extender to extend control distance. -
Page 7: How To Create Irregular Video Wall
User can convert project design drawings into 1920x1080 coordinates and pick up the coordinates at Top Left and Top Right corners in each LCD, then input to G-403 through OSD or GAlign tool to get the result. The Original Point for the coordinate system is set at Top Left corner as (0, 0). -
Page 8: Capture Coordinates From Picture By Microsoft "Paint
Please see YouTube at below: https://youtu.be/xc1D342Wa9g Example: 6x LCD video wall with 2x G-403. User can connect any LCD to any G-403 output. a、 To open the photo under [Paint] and trim the edge to active display area. b、 Resize the image in one edge to 1080 pixel height or 1920 pixel width and maintain aspect ratio. (It... - Page 9 G-403-3 c、 Open [File] [Properties] and resize the image to 1920x1080 resolution...
- Page 10 G-403-3 d、 Make sure the final resolution should be 1920*1080. Select [All], then move the image to the center of 1920x1080 coordinates by keyboard arrow key. e、 Click Top Left and Top Right corner in each LCD to collect the coordinates for each LCD. User can enlarge...
-
Page 11: How To Key-In Coordinates
[Top Left] & [Top Right] corner in each TV (LCD) then press [Write] to save the settings and execute the result to G-403. The result will be the same as manual upload via OSD. b、 To enable [Diagram], user can see the result on GAlign window. -
Page 12: Video Wall With Multiple Units Of G-403
G403 can be at different locations. User can use Video Wall [Zoom], [Pan] and [Overlap] function to crop, assign and align the final position among all G-403. All of the operations can be done through Remote Controller and OSD but not in GAlign PC tool. -
Page 13: Case Study A (Full Hd Signal Source)
V=1, #2 G-403: H=2, V=2 and increase [OVERLAP] value at the same time (select RH Edge for #1 G-403, LH Edge for #2 G-403) to let two G-403 images combine into one. This value can be calculated through the distance apart from image center line. -
Page 14: Case Study C (Video Wall With 15X 55" Lcd)
Adjust video wall image to expected location through [R] (Ratio) and [P] (Position) hot keys in remote controller. Power on G-403 again to finalize the settings to avoid frame tear in the image, then save final settings in [Profile] for permanent storage. -
Page 15: Comparison Between Landscape/Rotated Content In Portrait Display
PC or media player. The final resolution will be 1823x1080:1080x720=2.53x higher. c、 G-403 can handle both cases no matter the content has been rotated or not. However, user will get higher resolution image if the content can be pre-rotated. -
Page 16: How To Determine Source Signal Resolution For A Video Wall
In multiple G-403 application, user can adjust LCD position in each G-403 separately, then use [Video Wall] setting to combine them together. User can also combine all G-403 image together first, then adjust each LCD image position. g、 Please save the final result in [Profile]. -
Page 17: Example For Looping Playback Settings
G-403-3 b、 The display mode can show different display settings in each LCD, including different size, image location & rotation angle. Different aspect ratio and display position in entire video wall can be put into different display modes as well. -
Page 18: How To Change Display Aspect Ratio And Image Position
G-403-3 Select Index 2 and click [Write] command. Select Index 3 and click [Write] command. Select Index 4 and click [Write] command. Select Index 5 and click [Write] command. c、 To modify the settings for each Index ... -
Page 19: Other Notice
User will see flashing LED on front panel after press 85x number keys. It means the GeoBox with flash LED is locked and will not be controlled by remote controller. d、 Each G-403 is equipped with IR extenders. User can extend IR control distance up to 20m through 2.5mm audio cable.
Need help?
Do you have a question about the G-403 and is the answer not in the manual?
Questions and answers