Download
Share
Print this page
Insta Graphic Systems 158 Owner's Operation And Maintenance Manual
  1. Manuals
  2. Brands
  3. Insta Graphic Systems Manuals
  4. Power Tool
  5. 158
  6. Owner's operation and maintenance manual

Insta Graphic Systems 158 Owner's Operation And Maintenance Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
MNL90158
Rev. G 07.01.16
MODEL 158
OPERATION AND MAINTENANCE MANUAL

Advertisement

loading
Need help?

Need help?

Do you have a question about the 158 and is the answer not in the manual?

Questions and answers

Related Manuals for Insta Graphic Systems 158

Summary of Contents for Insta Graphic Systems 158

  • Page 1 MNL90158 Rev. G 07.01.16 MODEL 158 OPERATION AND MAINTENANCE MANUAL...

  • Page 2: Safety Summary

    Safety Summary International Symbols WARNING In case of power cord damage, Power Off do not attempt to repair or replace the power cord. Contact the manufacturer or the local Power On distributor. WARNING Hot Surface Hot Surface. Avoid contact. Risk of Electrical Shock CAUTION During normal operation, the Protective Earth Terminal...
  • Page 3 This warranty does not apply to any machine that has been subjected to misuse, negligence or Your model 158 machine will have a long, trouble accident. free life. Read this manual. Keep it with your machine; it's your key to proper operation and lasting Insta shall not be liable for the injury, loss or service.

  • Page 4: Degree Of Protection

    Non protected Objects greater Dripping water than 50mm Dripping water Objects greater Specifications when tilted up to than 12mm 15 deg. MODEL 158 Objects greater Spraying water than 2.5mm Voltage 120 Volts AC 50/60 Hertz Model 158 1750 Watts 14.6 Amps...

  • Page 5: Operation

    Environmental Conditions Operation Only operate Insta heat seal machines under 1. Turn the power on by pressing the POWER suitable environmental conditions. button on the controller. 1. Placed on a even, non flammable surface. 2. Set desired temperature and time. 2.
  • Page 6 Operation Timer/Temperature Temperature Control Solid State Controller Timer This controller has three (3) control features: 1. Temperature - Temperature may be set • The controller has a count down timer that from 225 - 450°F (107-232°C). automatically activates a buzzer at the completion of the application.
  • Page 7 Preventive Maintenance Replacement of Silicone Rubber Pads Suggestions The Insta heat seal machines are relatively 1. Make sure heat platen is cool. maintenance free. For long, trouble-free life, 2. Use tube of MPPC006 silicone adhesive the following preventive maintenance should be followed: sealant to bond the silicone rubber pad to metal platen.
  • Page 8 Safety and Danger Zone Diagram Hot Surface. Avoid contact with Upper Platen Shroud Do not handle the machinery with wet hands Keep hands clear Machinery should be operated under a secure flat surface...
  • Page 11 MPS90018 MPS90018 SCREW, PAN HD 4-40UNC x .50 LG. MHSR44012 MHSR44012 POWER CORD (USA MODEL) MPPW141 MPPW142 POWER CORD (EUROPEAN MODEL) MPPW202 POWER CORD (GREAT BRITAIN) MPPW203 SCREW, PAN HD 8-32UNC x .375 LG MHSP83238 MHSP83238     MODEL 158 070116   ...
  • Page 12 GAS SPRING, DAMPENER ASSEMBY MP158-001 MP158-001 NUT CAP DEEP DRAWN ½” STUD MH007-049 MH007-049 GROMMET, RUBBER 3/8” ID. 7/8” OD. MH007-050 MH007-050 PLATEN, HEAT ASS'Y MPP1381A MPP1382A PLATEN, HEAT (WIRING ONLY) MPP1381W MPP1382W PLATEN, LOWER ASS'Y MPP90160 MPP90160       MODEL 158 070116   ...
  • Page 13 FOR USE BY QUALIFIED PERSONNEL ONLY Notes:...
  • Page 14 FOR USE BY QUALIFIED PERSONNEL ONLY...
  • Page 15 FOR USE BY QUALIFIED PERSONNEL ONLY...
  • Page 16 13925 E. 166 St. • Cerritos, CA USA 90702 • (800) 421-6971 • Fax (562) 404-3010...