Page 1
B L A Z E P L U S ™ I N S T R U C T I O N S M A N U A L...
Page 3
Cautions for the first use Remember, safety should be your first priority. 1. Please make sure that you disconnect all other electronic devices connected to the power line you plan on using for your iron. 2. Make sure that you have removed any packaging or protective covers from the soleplate.
Safety Instructions 1. Whenever you need to step away from the iron, make sure that you unplug it and leave the iron in a vertical position with the soleplate facing upright. 2. Avoid children near the plugged iron. 3. Avoid contact of hot soleplate with your hands or flammable objects during use.
Page 5
Safety Instructions 1. Whenever you need to step away from the iron, make sure that you unplug it and leave the iron in a vertical position with the soleplate facing upright. 2. Avoid children near the plugged iron. 3. Avoid contact of hot soleplate with your hands or flammable objects during use.
Parts & Features 1. Water Filling Cover 6. 10 Foot Electrical Cord 2. Steam Control with 360º Pivot 3. Auto Surge™ Button 7. Heating LED Indicator Light 4. LED Indicator Pump Light & 3-Way 8. Heat Settings Dial Auto Shutoff Indicator Light 9.
Dry Ironing 1. Set the movable Steam Control Lever to point ‘’0’’. 2. Adjust ironing temperature in accordance with the linen’s requirement. Filling with Water Before filling the water tank, make sure that the iron is unplugged, temperature dial is positioned at the “OFF” mark, and the iron is held at approximately 45º...
Page 8
Auto Surge (Continuous Steam) 1. Fill the water tank in accordance with the instructions in the “Filling with Water” section. 2. Plug the cord into the outlet and ensure that the steam button is OFF. 3. Choose the fabric temperature desired. 4.
Auto Surge™ Button Vertical Steam By holding the iron in a vertical position, one can apply continuous steam to remove creases from curtains and any type of hanging fabrics. Anti-Drip An advanced system inside your iron prevents water leakage at even the lowest heat setting.
Anti-Calc Over time, lime scales may accumulate inside the iron or on the soleplate’s surface. To prevent this, an anti-calc filter is permanently installed in this appliance. It cannot be removed for cleaning purposes. Auto Shut-Off 1. If the iron is left unused for 15 minutes, the light will blink signaling that the iron has automatically shut off.
Page 11
Heat Settings Dial Caution Please note that this symbol on your fabric’s label means this article may not ironed.
Page 12
Heater cleaning 1. Before cleaning the heater, unplug the cord, empty the water tank, and make sure you have given the soleplate enough time to cool down. 2. Carefully turn your iron over, and pry up the cover plate by smoothly inserting a small spread-eagled-screwdriver into the prying part of the cleaning hole.
Cleaning & Maintenance Before you begin cleaning, unplug the iron and allow it to cool down. 1. Clean the soleplate with any moist cloth and non-abrasive cleaner. 2. If fibers stick to the soleplate, use damp cloth immersed in vinegar to wipe off adherent fibers.
Troubleshooting Problem Possible Reasons Solution Check thermostat dial and Cord may be unplugged or thermostat There is little heat or no look for any error in power improperly set. heat. transmission. Adjust thermostat dial to your Thermostat dial is set at the OFF mark. Steam has stopped or desired setting.
Page 18
HEAT RESISTANT HEAT RESISTANT PROTECTIVE 3-FINGER GLOVE IRONING GLOVE IRON CASE (MODEL: ER1033) (MODEL: ER1035) (MODEL: ER1050)
Page 19
EXTRA LARGE PROTECTIVE SILICONE IRON IRON & BOARD SUPER MAGNETIC IRONING MESH REST PAD HOLDER IRONING MAT (MODEL: ER1020) (MODEL: ER1040) (MODEL: ER1010) (MODEL: ER1025)
Page 20
THANK YOU FOR PURCHASING PRODUCTS FOR MORE INFO PLEASE VISIT: WWW.EUREKAGARMENTCARE.NET...
Need help?
Do you have a question about the Blaze Plus and is the answer not in the manual?
Questions and answers