Page 1
Wireless Internet Camera for ER-400 Installation Guide Catalog #100499 - Rev. C November 2009...
Page 3
Every effort has been made to make this book as complete and accurate as possible. However, no warranty of suitability, purpose, or fitness is made or implied. Intelitek is not liable or responsible to any person or entity for loss or damage in connection with or stemming from the use of the software, hardware and/or the information contained in this publication.
Table of Contents Getting Started Chapter 1: Unpacking the Equipment ..................1 System Requirements ....................1 Camera Kit Components..................1 Installing the ViewFlex System................2 Mounting the Camera Chapter 2: 12V Power Supply Convertor..................3 Attachment of Camera Mounting Shelf..............4 Mount Camera ......................5 Option A: Bottom Mount................5 Option B: Top Mount ..................6 Power Connection....................6 Connecting the Software Protection Key...
313005 1/4" Flat Washer 330223 Allen wrench set (3 mm and 4 mm x 6 cm) 330225 Allen wrench (3/16" x 5") 330209 Allen wrench (4 mm x 14.5 cm) Wireless Internet Camera for ER-400 Installation Guide Getting Started (0911)
Installing the ViewFlex Software, page 9 Connecting the Internet Camera to your Computer, page 13 Installing the Internet Camera Software, page 15 Software Configuration, page 21 Wireless Internet Camera for ER-400 Installation Guide Getting Started (0911)
12V Power Supply Convertor The power supply converts the 24-volt electricity from the AGV's batteries to the 12 volts required for operation of the camera. 24V Power Supply Camera Cable Wireless Internet Camera for ER-400 Installation Guide Mounting the Camera (0911)
Camera Mounting Shelf. b. Insert two T-slot nuts (part # 312007) into the profile slot. c. Insert two 3mm Allen screws and tighten with a 3-mm Allen wrench. Profile Slot Wireless Internet Camera for ER-400 Installation Guide Mounting the Camera (0911)
Mount Camera Your Internet camera may be mounted on either the top surface or the bottom surface of the Camera Mounting Shelf. Intelitek recommends that you mount it on the bottom surface for better protection from falling objects. Option A: Bottom Mount Procedure: 1.
2. Position the Camera Anchor Bracket (part # 110330) around the base of the camera, and secure in position using two Pan-Head Phillips screws, flat washers and nuts. Power Connection Connect the power cable from the power supply to the camera. Wireless Internet Camera for ER-400 Installation Guide Mounting the Camera (0911)
30-day trial basis. To connect the software protection key, plug the software protection key into a USB port in your computer. Software Protection Key Wireless Internet Camera for ER-400 Installation Guide Connecting the Software Protection Key (0911)
You must first install the Image Processing Tool module. Only then can you install the ViewFlex software. 3. Click on Image Processing Tool. The Matrox Inspector setup will begin to run. 4. Follow the instructions on your screen. Wireless Internet Camera for ER-400 Installation Guide Installing the ViewFlex Software (0911)
Page 16
7. Start the installer by clicking on the icon of the CD drive in My Computer. The ViewFlex Setup window is displayed, as shown on page 9. 8. Select ViewFlex. A Welcome window is displayed. Welcome Window Wireless Internet Camera for ER-400 Installation Guide Installing the ViewFlex Software (0911)
Page 17
9. Click Next. A License Agreement window is displayed. 10. Select the I accept the terms of the license agreement radio button, and click Next. 11. The Installation window is displayed. Installation Window Wireless Internet Camera for ER-400 Installation Guide Installing the ViewFlex Software (0911)
Page 18
14. Select Yes, I want to restart my computer now. when prompted at the end of the installation process. 15. Plug the software protection key into the USB port of your computer. 16. Click Finish. The computer will restart. Wireless Internet Camera for ER-400 Installation Guide Installing the ViewFlex Software (0911)
Connect your Internet Camera directly to the Ethernet port on your PC using a crossover Ethernet cable. The crossover cable is not provided as part of the Internet Camera Kit. Wireless Internet Camera for ER-400 Installation Guide Data Connection for Setup...
1. Select Start | Control Panel | Network Connections | Local Area Connection. 2. Select Properties. 3. Under the General tab, select Internet Protocol (TCP/IP) and Properties. Wireless Internet Camera for ER-400 Installation Guide Installing the Internet Camera Software (0911)
Page 22
5. The subnet mask 255.255.255.0 will be automatically entered. 6. Click OK. 7. Start Internet Explorer. 8. Select Tools | Internet Options from the menu bar at the top. Wireless Internet Camera for ER-400 Installation Guide Installing the Internet Camera Software (0911)
Page 23
11. Click OK to return to the Internet Options dialog. 12. Click OK. 13. Insert the D-Link Installation CD-ROM into the CD-ROM drive of your PC. 14. The installation screen is displayed. Click Install Software. Wireless Internet Camera for ER-400 Installation Guide Installing the Internet Camera Software (0911)
Page 24
IP addresses. 16. In Internet Explorer, save the IP address of the camera in the Favorites folder. 17. In the D-Link Installation Wizard, select Setup. 18. Select Configuration. Wireless Internet Camera for ER-400 Installation Guide Installing the Internet Camera Software (0911)
Page 25
21. In the upper part of the window, next to the camera image, you have controls for pan and tilt. Using these controls, choose a home position for your camera. 22. As shown, assign position #1 to this position and select Add. Wireless Internet Camera for ER-400 Installation Guide Installing the Internet Camera Software...
Page 26
25. In this panel, you have many options for audio and video settings, including the image size. The choices offered to you depend on whether you have purchased a PAL format camera or an NTSC format camera. Wireless Internet Camera for ER-400 Installation Guide Installing the Internet Camera Software...
Viewflex to work with your new camera. These entries must be made in the CamSettings.ini file, found in the following location: Windows XP: C:\Documents and Settings\All Users\Documents\Intelitek\VCTRL Windows Vista: C:\Users\Public\Documents\Intelitek\VCTRL Procedure: 1.
Arrow up - Moves up. Arrow down - Moves down. Home – Returns the camera to home position For all other ViewFlex features refer to the ViewFlex user manual. Wireless Internet Camera for ER-400 Installation Guide ViewFlex for D-Link Camera Interface (0911)
Demo Program Description A single wireless Internet camera for the ER-400 AGV may be tested with the CAM_PAN_TILT demo project. System Requirements The demo project has the same minimum system requirements listed on page 1. Such a system is sufficient for 352 x 240 images for PAL video and 320 x 240 for NTSC video.
(including Matrox Image Processing), version 3.1 (from the ViewFlex CD- ROM) Share the directory where Scorbase is installed on the desktop PC so that the laptop PC can access it. The default installation directory is C:\Intelitek\SCORBASE\AGV\CIMFlex Wireless Internet Camera for ER-400 Installation Guide Demo Program (0911)
10. Select and load the project CAM_PAN_TILE.WS. 11. Select Open CIM Screen from the Window menu. This screen will display messages from the AGV Device Driver. 12. Run the Scorbase program named CAM_PAN_TILT. Wireless Internet Camera for ER-400 Installation Guide Demo Program (0911)
Need help?
Do you have a question about the ER-400 and is the answer not in the manual?
Questions and answers