Note This signal word indicates important information (e.g. material damage), but does not indicate hazards. Info Information marked with this symbol helps you to carry out your tasks quickly and safely. cordless screwdriver with bit magazine PSCS 11-3,6V...
Use of a cord safety principles. A careless action can cause severe suitable for outdoor use reduces the risk of electric shock. injury within a fraction of a second. cordless screwdriver with bit magazine PSCS 11-3,6V...
Page 4
• Have your power tool serviced by a qualified repair tool in unexpected situations. person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. cordless screwdriver with bit magazine PSCS 11-3,6V...
Page 5
PSCS 11-3,6V for screwing in and loosening screws, while adhering to and following the technical data. Wear eye and mouth protection when processing We recommend using the power tool with original Trotec materials that may contain harmful substances (e.g. accessories. asbestos).
Page 6
If necessary, use a pipe detector to check the wall you want to drill in or slit open. Warning Risk of injuries caused by flying parts or bursting tool heads. cordless screwdriver with bit magazine PSCS 11-3,6V...
Vibration information according to EN 60745 Handle Vibration emission value 0.216 m/s drilling in metal / screwing Charger connection ah=in LED work light Uncertainty K 1.5 m/s 25 mm bit Charger On / off switch Bit magazine cordless screwdriver with bit magazine PSCS 11-3,6V...
When the device is not being used, observe the following storage conditions: • dry and protected from frost and heat • ambient temperature below 40 °C • protected from dust and direct sunlight cordless screwdriver with bit magazine PSCS 11-3,6V...
The device cannot be started when the charger is connected. The on / off switch (11) can be pressed, but the motor will not start. The LED work light (8) and the battery level indication (4) light up. cordless screwdriver with bit magazine PSCS 11-3,6V...
Page 10
1. Set the switch for clockwise/counter-clockwise rotation (5) to centre position (lock). 2. Pull the slide switch for bit exchange (3) forward. ð The current bit is pushed into the bit magazine (12). cordless screwdriver with bit magazine PSCS 11-3,6V...
Page 11
ð The current bit is pushed out of the bit magazine (12) the bit magazine out to the left. into the magnetic bit holder (1). 4. Take the bit magazine (12) off the holder (14). 5. Remove bits which are no longer needed from the bit magazine (12). cordless screwdriver with bit magazine PSCS 11-3,6V...
5. Let go of the on / off switch (11) to stop the device. ð The LED work light (8) turns off. Info The motor has an integrated brake that quickly stops the motor once you let go of the on / off switch (11). cordless screwdriver with bit magazine PSCS 11-3,6V...
Contact the Trotec customer service. • Check the charger connection for dirt. Remove any dirt. • The battery might be defective. Contact the Trotec customer service. The device does not start: • The battery power might be too low. Recharge the battery.
• Keep the connecting terminals on the device and charger clean. • Keep the ventilation openings free from dust deposits to prevent overheating of the motor. 7. Dispose of the battery and the device as described in the Disposal chapter. cordless screwdriver with bit magazine PSCS 11-3,6V...
Manufacturer and name of the authorised representative of the technical documentation: Trotec GmbH & Co. KG Grebbener Straße 7, D-52525 Heinsberg Phone: +49 2452 962-400 E-mail: info@trotec.de Place and date of issue: Heinsberg, 01.06.2016 Detlef von der Lieck, Managing Director cordless screwdriver with bit magazine PSCS 11-3,6V...
Page 17
Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...