Related Manuals for Cineo Standard 410
Summary of Contents for Cineo Standard 410
- Page 1 User Guide Revision 2.2 — August, 2018 Information and specifications in this document are subject to change without notice. w w w . c i n e o l i g h t i n g . c o m...
- Page 2 Cineo’s Photo-Accurate Dimming™ maps the HSX with innovative saturated color technology, 0-100% dimming curve to actual camera stops the Standard 410 delivers up to 25,000 lumens of for precise output control using the DIM control beautiful, easily controllable, full-gamut light across locally or on the 1st DMX channel.
-
Page 3: General Notes
The Standard 410 weighs 28 lbs. (12.7 kg) excluding accessories. The combined weight should be considered when choosing a suitable safety cable. Safety cables must securely be attached to the yoke on Standard 410 and should be as short as possible to reduce travel distance if primary hanging accessory fails. - Page 4 System Components, Connections and Controls All connectors and system controls for the Cineo Standard 410 are located on the back of the unit. In addition to its full color heads-up display, optically encoded rotary knobs give access to menu selections and local control inputs.
- Page 5 Power The Standard 410 unit is controlled by an internal power supply. 110 – 220VAC is provided to the unit via a locking IEC connector, located on the back control panel. NOTES: 1. Ensure the power cable is disconnected before servicing.
- Page 6 The CIE 1931 diagram opposite illustrates the Standard 410 color space. Controls Setup of the Standard 410 is can be accomplished either using the large knob with the CONTROL and STATUS displays, or remotely using RDM. Standard 410 Setup Menus Operational parameters for the Standard 410 are managed through the Setup Menus.
-
Page 7: Local Mode
Screen contextually switches to show the value of each control being adjusted. Lower left knob (Large) Photo-Accurate Dimming The dimming curve on the Standard 410 follows a strategy that provides relative output levels that correspond to image capture. Both DMX values and local control levels directly correlate to camera stops in a meaningful way. -
Page 8: Dmx Mode
Lower right knob: CCT Adjustment The color temperature (CCT) of the fixture is controlled by turning the lower right knob in a continuously variable range of 2700K to 6500K. Pushing the lower right knob cycles the CCT of the fixture between popular settings: 2700, 3200, 4300, 5600 and 6500K. - Page 9 8-BIT vs 16-BIT Standard DMX data structure is 8-bit, which limits the value range between 0-255. This is the preferable operating mode for maximum compatibility with DMX controllers. If more precise control is required, the unit can be operated in 16-bit mode, offering a value range of 0-65,535.
- Page 10 For example, if all values of Red, Green and Blue are equal, the resultant white light emanating from the fixture will be at the CCT determined by the CCT control. In actuality, the Standard 410 correlates the RGB values in combination with the white LEDs to maintain a very accurate, high-CRI white light value. Equal values of Red, Green and Blue, each at 50% are the equivalent of a white light dim level of 50%.
-
Page 11: User Presets
User Presets The Standard 410 can store and recall up to 6 separate groups of settings, which are saved until over-written or a factory reset... - Page 12 To store a group of settings, select the PRESETS menu option. Initially, the system presents 6 storage locations, labeled A-F. Turn the large knob to the desired storage location, push the large knob and the current settings for the fixture will be stored in that location.
- Page 13 • Pin 5: Spare Wireless DMX Control The Standard 410 built-in wireless receiver runs on CRMX / Lumen Radio protocol which can receive signals from CRMX and some WDMX transmitters. Please note that each fixture can only be linked to a single transmitter at a time, and maintains the transmitter ID of its previous linking.
-
Page 14: Mounting Options
5 VDC, 500ma power to attached devices. Refer to installation instructions supplied with software upgrade. Mounting Options The Standard 410 has a fully rotational yoke with a TVMP mount. The standard yoke can be removed, and an optional Pole-Op yoke can be attached. -
Page 15: Specifications
Specifications Input Power: 110-240VAC, 410 watts max. via locking IEC connector Integrated power supply Fixture Size: 12” x 24 x 4.5” (37.4cm x 61cm x 11.5cm) Diffuser Size: 11” x 23” Weight: 28 lbs. (12.7 kg.) Mounting yoke includes TVMP Variable saturated color with presets at Red, Yellow, Green, Cyan, Blue, Magenta Variable white/color blending Local and Remote dimming, 0-100%... -
Page 16: Burning Injuries
Proper ventilation must be provided. ESD and LED’s LED components used in the Standard 410 are ESD (Electro-Static Discharge) sensitive. To prevent the possibility of destroying LED components do not touch either while in operation or when switched off. - Page 17 If the Product fails to work as warranted, Cineo Lighting will, in its sole discretion, repair or replace the Product with a new or remanufactured Product that is at least equivalent to the original Product.
- Page 18 Specifications are subject to change without notice. Cineo Lighting and Cineo Standard 410 are registered trademarks of Cineo Lighting, Inc. ©2018 Cineo Lighting, Inc. v2 08-22-18 Cineo Lighting P.O. Box 808 El Granada, CA 94018 Silicon Valley | Los Angeles | New York info@cineolighting.com...
Need help?
Do you have a question about the Standard 410 and is the answer not in the manual?
Questions and answers