Oregon Scientific PRYSMA B Manual

Getting started - Line Drawing
Getting started - Line Drawing
EN
Placement of the main unit
INtroductIoN
Thank you for selecting the Oregon Scientific™ Projection In/Out Thermo
Clock. This device bundles precise time keeping, alarm, and temperature
monitoring features into a single tool you can use from the convenience
of your home. Keep this manual handy as you use your new product.
It contains practical step-by-step instructions, as well as technical
specifications and warnings you should know.
Product INtroductIoN
Lcd display
Time Display
• Place the device as far as possible from computers and microwaves to
avoid interference with reception.
• Only use this device indoors in a dry location.
Unpacking the product Connecting the main unit to power
• Leave space around the device for ventilation purposes, so that the
warm air can escape freely.
• To ensure for good sound quality, do not cover the speaker.
Weather Placement of the remote thermo sensor (tHN129H)
Forecast
Indicator
Outdoor Temperature Indoor Temperature
Display Display
Lcd display
Symbol Description Function
Radio signal reception to Indicates the strength of the
outdoor unit (THN129H) radio reception
• Ideal placements for the sensor would be in any location outside the
Indicates low battery power of
Placement of the main unit
Low battery
home at a height of not more than 5 ft (1.5 m), shielded from direct
outdoor unit (THN129H)
sunlight or wet conditions.
Alarm 1 on
Appears when an alarm is Depending on conditions, the maximum radio signal reach is 50 m.
NOTE
activated
Alarm 2 on
KEy dEscrIPtIoNs
Shows outdoor temperature of
top
OUT 12345 Outdoor sensor reading
selected sensor.
IN Indoor sensor reading Shows indoor temperature
sNooZE button
ZONE Time zone Indicates selected time zone
Back
Sunny Weather forecast indicator
Cloudy Weather forecast indicator
Rainy Weather forecast indicator
Temperature button
Set/Alarm button
button
Snowy Weather forecast indicator
Projection
Micro USB jack
°c / °F button
Flip 180° button
sEttING tImE maNuaLLy
• Press and hold . The screen displays ZoNE and the number flashes.
• Press once or press and hold
UK, the time-zone offset sets the clock up to +/- 23 hours from the
received clock signal time.
• Press to confirm.
Time Display Outdoor Temperature Display
• Press once or press and hold
Focus length (1.5m – 2m) hour format, hour, minute, year, calendar format (month-day/day-
NOTE
month), month and date.
• Press again to confirm.
GEttING startEd
dIsPLayING tImE aNd datE
connecting the main unit to power supply
• Press to toggle between time and date display.
aLarm FuNctIoN
You can set two different alarm times with this clock.
setting/adjusting alarm time
• Press and hold .
• Use and
• Use and
• The alarm time is displayed. The alarm sound will stop after 2 minutes.
snooze function
• To use the sNooZE function, press the sNooZE button on top of
the clock when the alarm sounds. The alarm will stop and start again
Connect the power cable to the Micro USB jack and plug the power
after 8 minutes.
adaptor into a suitable power outlet.
displaying the alarm time
By default the clock will show the current time and date.
Inserting batteries into remote thermo sensor
• To display Alarm 1 for 5 sec, press
• To display Alarm 2 for 5 sec, press
activating/deactivating the alarm
• Press to activate/deactivate alarm in sequence:
Alarm1 > Alarm 2 > Both ON > Both OFF.
BacKLIGHt
• Press the Light button to toggle the desired backlight display
brightness level.
ProjEctIoN
• Slide the battery compartment cover open and insert 2 "AAA" batteries,
matching the polarity as shown, then replace the cover.
• Press rEsEt inside the sensor after each battery change.
Unpacking the product Connecting the main unit to power
The projector displays the time on your ceiling for easy viewing in a
darkened room.
• To activate the projection function for 5 seconds, press the sNooZE
button.
This function only works when the projection function is turned OFF.
NOTE
• To turn projection ON and OFF press and hold Light to toggle
between options. (The default setting is ON)
• To flip the projection content by 180°, press Flip 180°.
Max 50m
Max 1.5m
tEmPEraturE FuNctIoN
The temperature is measured in °C or °F.
• Press °C / °F to toggle between Centigrade (°C) and Fahrenheit (°F).
Placement of the main unit
The current indoor temperature is always displayed in the lower right
corner of the LCD display. To receive outdoor temperature information, you
Inserting batteries into remote thermo sensor
can connect up to 5 remote sensors to the main unit:
• Press & to toggle between channels (1 to 5) and display the
outdoor temperature of different sensors.
• Press and hold and for 2 seconds to start searching for remote sensors.
• Press and hold and for 2 seconds to enable auto-scan function for
the 5 channels. Information from Channel 1,2,3,4,5 will automatically
be displayed in sequence.
rEsEttING tHE cLocK
Whenever the clock is not behaving as expected, press Reset with the
point of a blunt object such as a stylus or ball point pen.
This will return all settings to default values.
NOTE
Max 50m
rEmotE sENsor
Max 1.5m
The main unit can collect temperature data from up to 5 sensors, and
should be placed within 50m (164ft) of the main unit. The amber LED
Indicator on the front of the sensor will blink to indicate that the unit is
transmitting a signal.
cH Channel 1-5. If more than one sensor is being used, make sure
each one has a different channel number.
Clock button
rEsEt Press if the sensor is not working correctly or if the batteries
button
have been replaced.
Before placing the remote sensor outdoors, check that the battery
NOTE
compartment door is closed properly,
sPEcIFIcatIoNs
maIN uNIt
L x W x H
Weight
reset button
Light button
Operating range
Temperature resolution
Temperature unit
rEmotE tHErmo sENsor (tHN129H)
and to adjust the setting. For EU/
L x W x H
Weight
and to adjust the setting for 12/24h
Operating range
Temperature resolution
No. of channel selectable 5
RF Transmission range
Radio-controlled clock (RCC) feature is not available for BAA223PNH.
NOTE
saFEty
Please observe the following safety precautions when setting up and
using this product.
• The manufacturer assumes no liability for possible damages that may
to adjust the hour and press to confirm.
have been caused by incorrect usage or mishandling of the device.
to adjust the minute and press to confirm. • Prior to using the device for the first time, check to make sure that
your household power supply corresponds to the voltage listed on
the device.
• LCD panel - The LCD panel is made of glass and may break if the unit
is dropped or impacted.
• Heat sources - Keep the product away from heat sources such as
radiators, stoves, heaters and other heat-generating products.
• Water and moisture - Do not use the unit in or near water or in high
moisture areas such as bathrooms.
and . • Power cord - If the power cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified persons in
and .
order to avoid a hazard.
• Repair - Do not attempt to repair or modify the unit yourself.
Contact the retailer or a qualified repairman if the product requires
servicing. Only use replacement parts that are recommended by the
manufacturer.
• Danger of suffocation! Keep all packaging material away from children.
carE
This product is designed to give you years of service if handled properly.
Oregon Scientific will not be responsible for any deviations in the usage of
the device from those specified in the user instructions or any unapproved
alterations or repairs of the product. Observe the following guidelines:
• Attention! Before cleaning disconnect the power plug from the socket.
• Cleaning - Use a damp cloth to wipe the unit. Do not use liquid
cleaning agents, benzene, thinner or aerosols.
• Projector lens - A dirty lens can result in a blurred projection. From time
to time, check to see if dust or other dirt has collected on the lens. Dust:
blow the dust from the lens with a brush/blower made for cameras
(available at an authorised dealer). After that, brush the lens lightly with
the brush and then blow dust off the lens again.
Fingerprints: If the lens does not become clean by using the brush/
blower, use a cotton swab, dipped in a special cleaning solution and
remove the dirt beginning from the middle and proceeding to the outside.
• Do not scratch the LCD display with hard objects.
• Never immerse the product in water. This can cause electrical shock
and damage the product.
• Do not subject the main unit to extreme force, shock, or fluctuations in
temperature or humidity.
• Do not tamper with the internal components.
• Ventilation - The vents and other openings are designed to keep the
unit cool and should not be blocked or covered. Preventing ventilation
can lead to overheating and may damage the unit.
advIcE rEGardING BattErIEs
• Do not expose batteries to extreme heat like direct sunlight, fire, etc.
• Batteries do not belong in household waste! Expired batteries must
be disposed of in an environmentally friendly way and according to
the applicable legal regulations.
• Batteries are very dangerous if swallowed. Please keep expired
batteries away from children at all times. If a battery is swallowed,
seek medical attention immediately.
• Batteries must not be recharged or activated with another means,
dismantled, thrown into fire or short-circuited.
• Do not mix new and old batteries or batteries of different types.
• Do not use rechargeable batteries with this product.
• Remove the batteries if storing this product for a long period of time.
• The batteries must be removed prior to disposing of the device.
BAA223PNH
The technical specification of this product and contents of this user
NOTE
guide are subject to change without notice. Images not drawn to scale.
aBout orEGoN scIENtIFIc
Inserting batteries into remote thermo sensor
Visit our website www.oregonscientific.com to learn more about
Oregon Scientific products.
For further assistance, please contact our Customer Services
at http://global.oregonscientific.com/customerSupport.php.
Oregon Scientific Global Distribution Limited reserves the right to interpret
and construe any contents, terms and provisions in this user manual and
to amend it, at its sole discretion, at any time without prior notice. To the
extent that there is any inconsistency between the English version and
any other language versions, the English version shall prevail.
Fcc statEmENt
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the
WARNING
party responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the
NOTE
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the nterference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
dEcLaratIoN oF coNFormIty
The following information is not to be used as contact for support or sales.
Please call our customer service number
(listed on our website at www.oregonscientific.com),
or on the warranty card for this product for all inquiries instead.
We
Name: Oregon Scientific, Inc.
Address: 10778 SW Manhasset Dr.
UNIT B-2 Tualatin,
OR 97062 USA
Telephone No.: 1-800-853-8883
declare that the product
Product No.: BAA223PNH
Product Name: Projection Clock
Manufacturer: IDT Technology Limited
Address: Block C, 9/F, Kaiser Estate,
Phase 1, 41 Man Yue St.,
Hung Hom, Kowloon, Hong Kong
is in conformity with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: 1) This device may not cause harmful
interference. 2) This device must accept any interference received,
including interference that may cause undesired operation.
Eu-dEcLaratIoN oF coNFormIty
22 x 200 x 80 mm
Hereby, Oregon Scientific, declares that this Projection Clock
(Model: BAA223PNH) is in compliance with EMC directive 1999/5/
224 g without batteries
EC. A copy of the signed and dated Declaration of Conformity is
available on request via our Oregon Scientific Customer Service.
-5.0 °C to +50.0 °C (23.0 °F to 122.0 °F)
0.1 °C (0.2 °F)
°C/°F
125 x 50 x 19.5 mm
59 g without batteries
-20 ºC to +60 ºC (-4 ºF to 140 ºF)
0.1 ºC (0.2 ºF)
50 m (164 ft) unobstructed
sc
• 放置传感器的理想地方，是家居户外任何不高于5 英呎(1.5 米)的位
产品描述
置，并需避免放置在阳光直射和潮湿的环境下。
谢谢阁下选购Oregon Scientific TM PRYSMA B 稜光溫度投影時計。
此装置集精确时计、闹钟及温度监察功能于一身，十分适合于家居中
视乎环境而定，无线电讯号传输最远可达50米。
注
使用。使用新产品时，请将此手册存放于当眼的地方。手册中包含各
步骤的使用说明，以及你需要留意的技术规格及警告。
按钮描述
产品简介
顶部
LCD 显示屏
时间显示
小睡 (背面灯 / 投影) 按钮
背面
天气预报
显示
户外温度显示 户内温度显示
温度按钮
LCD显示屏符号
设置/闹钟按钮
符号 描述 功能
户外装置 (THN129H)的
按钮
指示无线电讯号接收的强度
无线电讯号接收
表示户外装置 (THN129H)
电量不足
的电量不足
闹钟 1 已开启 当闹钟启动时，
闹钟2 已开启 此图标便会显示
OUT 12345 户外传感器读数 显示所选传感器的户外温度
IN 户内传感器读数 显示户内温度
Micro USB 插头
ZONE 时间区域 显示所选的时间区域 °c/°F按钮
180°转向按钮
天气预报显示 天气预报显示
手动设置时间
阴天 天气预报显示 • 长按 。画面会显示ZONE (区域)，号码会闪动。
• 按一次或长按
接收到的时钟讯号时间，来设置时钟最多为+/- 23 个小时。
下雨 天气预报显示
• 按 以确定。
• 单击或长按
下雪 天气预报显示 行事历格式 (月-日/日-月)、月份及日期。
• 再按 以确定。
显示时间及日期
投影器
• 按 以在时间和日期显示之间切换。
闹钟功能
利用此时钟，你可以设置两个不同的响闹时间。
设置/调敎响闹时间
• 长按 .
• 使用 及
• 使用 及
• 装置会显示响闹时间，而响闹声音会于2 分钟后停止。
贪睡回叫功能
• 要使用SNOOZE (贪睡) 功能，请当响闹响起时，在时钟的顶部按
显示户外温度
显示时间 SNOOZE (贪睡)按钮。8 分钟后响闹会停止并再次开始。
距离范围(1.5 米 – 2 米)
注
显示响闹时间
默认下，时钟会显示现时时间及日期。
• 要持续5秒来显示响闹1，请按
开始使用
• 要持续5秒来显示响闹2，请按
将电源连接至设备
启动/关闭闹钟
• 按 以启动/关闭闹钟，次序为：
闹钟 1 >闹钟2 > 同时开启两个闹钟 >同时关闭两个闹钟。
背面灯
• 按Light(灯)按钮，以将背面灯的光暗度切换成喜欢的显示程度。
投影
把电源线连接至Micro USB 端口，然后把电源插头插入适合的电源
插座中。
把电池装入远程热能传感器
投影器会在天花板上显示时间，以方便在黑暗的房间中查看。
• 要持续地开启投影功能5秒，请按下SNOOZE (贪睡) 按钮。
此功能只在投影功能为 OFF (关闭) 时才有效。
注
• 要把投影功能 ON (开启)及OFF(关闭)，请长按Light (灯光)以在选
• 滑动电池槽盖以开启，并如图示般配合极性来放入2 粒「AAA」电 项之间切换(默认值为ON (开启))。
池，然后放回电池槽盖。
• 要把投影内容以180°转向，请按Flip 180°(转向180°)。
• 每次更换电池后，请按下传感器中的RESET (重置) 键。
温度功能
温度会以°C 或°F来测量。
放置主装置
• 按下°C / °F 以在摄氏(°C)及华氏(°F)之间切换。
当前的户内温度会于LCD 显示屏的右下角显示。要接收户外温度信
息，你最多可以把主装置连接到5 个远程传感器：
• 按下 以在频道 (1 至 5) 之间切换，并显示不同传感器的户外温度。
• 长按 及
• 长按 及
3、4、5 收到的信息会自动以顺序方式来显示。
重置时钟
• 把装置尽量放置得远离计算机及微波炉，以避免接收障碍。
当时钟不能正常运作，请以不锋利对象的顶端，如手写笔或圆珠笔来
• 只在户内的干燥环境中使用此装置。
按Reset (重置)。
• 请在装置周围预留空间以作通风之用，以令暖空气得到流通。
这样做会把所有设置变回默认值。
注
• 要确保声音质量良好，请勿遮盖扬声器。
放置远程热能传感器(THN129H)
Max 50m
Max 1.5m
时钟按钮
按钮
重置按钮
灯光按钮
及 来调整设置。对于欧洲/英国，时区偏移会从
及 来调教 12/24 小时格式、小时、分钟、年份、
来调教小时并按 来确定。
来调教分钟并按 来确定。
及 。
及 。
2 秒，以开始搜索远程传感器。
2 杪，来为5 个频道开启自动扫描功能。从频道 1、2、