Perfomance Tool M662 Owner's Manual

PARTS LIST
NO. DESCRIPTION QTY NO. DESCRIPTION
1 Body 1 14 Bearing
2 O-Ring 2 15 Rear Cover
3 O-Ring 1 16 Rotor
4 Pin 1 17 Blade
5 O-Ring 3 18 Cylinder
6 Tube 1 19 Pin
7 Trigger Spring 1 20 Front Cover
8 Trigger 1 21 Gasket
9 Screw 2 22 Gear
10 Trigger Pin 1 23 Gear Pin
11 Exhaust Diffuser 1 24 Spindle
12 Screw 2 25 Ring
13 Connector 1 26 Bearing
TROUBLESHOOTING
INSuFFICIENT POWER:
Probable Cause Solution
Dirty or clogged air passages . . . . . . . . . . . . . . . . . .Flush and lubricate tool, drain air tank and supply line
Insufficient air supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Increase line pressure, Make sure compressor
matches tool's air pressure and consumption needs
Air leakage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Use PTFE tape at all fittings and joints . Check tool for
worn or damaged O-rings & seals .
Worn/damaged wear & tear parts . . . . . . . . . . . .Replace as necessary .
Tool matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Be sure you are using a tool suited for the torque
requirements of the job at hand .
QTY NO. DESCRIPTION QTY
2 27 Lock Ring 1
1 28 Washer 1
1 29 Spindle Nut 1
5 30 Bearing 1
1 31 Blade Housing 1
2 32 Screw 1
1 33 Block 1
1 34 Center Blade 2
3 35 Left Blade 2
3 36 Bushing 1
1 37 Right Blade 2
1 38 Wrench 2
2
HEAVY DUTY METAL SHEAR
Stock Number M662
OWNER'S MANUAL

SPECIFICATIONS:

Cutting Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 GA
Air pressure (P .S .I .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Average air consumption (C .F .M .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Free speed (R .P .M .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,500
Air inlet (N .P .T .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4
Hose size (I .D .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8 in .
Length (IN .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 .5
Weight (LBS .) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 .6
Specifications are subject to change without notice .
WARNING!
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND
WARNINGS BEFORE OPERATING THIS TOOL . FAILURE TO DO SO
MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE
AND WILL VOID WARRANTY .