Quick Start Guide
Connect Primary Lyra to Modem
Setup your Lyra WiFi system
Unplug your cable / DSL
modem*. Remove the
battery if it has one.
Download the free ASUS Lyra app.
* If you are using DSL for
Launch the ASUS Lyra app on your mobile
internet, you will need
device, and follow the instructions in just
a few moments.
from your Internet
service provider (ISP) to
* Make sure your device supports BLE,
properly configure your
Bluetooth 4.0 or above.
Connect your modem to Lyra with the
network cable provided.
Power on your cable / DSL modem, and
check your cable / DSL modem LED lights
to ensure the connection is active.
Plug in the power adapter to Lyra and
wait until the LEDs turn to solid white to
Through Web GUI
ensure that your Lyra is ready for setup.
Connect PC/NB to your Lyra via WiFi
"ASUS_XX_AMAPS". Open a web browser.
You will be redirected to the ASUS Setup
Wizard. If not, navigate to http://router.
Adding other Lyra to current network
Through Web GUI
Launch Lyra app and click the "+" icon on
Press the Pairing button on the Primary Lyra
the upper right corner, then choose Add
until the LED starts to blink green light.
Lyra to current network and follow the
Press the Pairing button on the second Lyra
instructions to complete.
until the LED starts to blink green light, then
turns solid light cyan, indicating the pairing
process is completed.
* Pairing feature only works with the Primary Lyra
device connecting to modem.
Colors of Lyra
* While setting up through Web GUI, ensure that
you pair other Lyra hub(s) with the Primary Lyra
using the Pairing button.
Everything is good!
Loss connection to the primary Lyra. Move it closer.
Loss connection to the Internet. Please check the cable connected with your modem.
Lyra is ready for setup. It will start blinking when setting up with the app.
Lyra is booting up or applying settings.
S13319 / Primera edición/ Septiembre 2017
Federal Communications Commission
RF exposure compliance. To maintain compliance with FCC
exposure compliance requirement, please follow operation
instruction as documented in this manual.
This device within the 5.15 ~ 5.25 GHz is restricted to indoor
This device complies with Part 15 of the FCC Rules. Operation is
operations to reduce any potential for harmful interference to
subject to the following two conditions:
co-channel MSS operations.
• This device may not cause harmful interference.
Radio Frequency (RF) Exposure
• This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
f or a class B dig ital device, pursuant to part 15 of the FCC Rules.
The radiated output power of the ASUS Wireless Device is below
These limits are designed to provide reasonable protection against
the Industry Canada (IC) radio frequency exposure limits. The
harmful interference in a residential installation. This equipment
ASUS Wireless Device should be used in such a manner such
generates, uses and can radiate radio frequency energy and, if not
that the potential for human contact during normal operation is
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
This device has been evaluated for and shown compliant with
guarantee that interference will not occur in a particular installation. If
the IC Specific Absorption Rate ("SAR") limits when installed in
this equipment does cause harmful interference to radio or television
specific host products operated in portable exposure conditions
reception, which can be determined by turning the equipment off and
(antennas are less than 20 centimeters of a person's body).
on, the user is encouraged to try to correct the interference by one or
This device has been certified for use in Canada. Status of the
more of the following measures:
listing in the Industry Canada's REL (Radio Equipment List) can be
• Reorient or relocate the receiving antenna.
found at the following web address:
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
Additional Canadian information on RF exposure also can be
that to which the receiver is connected.
found at the following web: http://www.ic.gc.ca/eic/site/smt-gst.
• Consult the dealer or an experienced radio/TV technician for help.
RF Exposure information
This device meets the EU requirements (2014/53/EU) on the
Any changes or modifications not expressly approved by the party
limitation of exposure of the general public to electromagnetic
responsible for compliance could void the user's authority to operate
fields by way of health protection.
Prohibition of Co-location
• Use this product in environments with ambient temperatures
between 0°C(32°F) and 40°C(104°F).
This device and its antenna(s) must not be co-located or operating in
• Refer to the rating label on the bottom of your product and
conjunction with any other antenna or transmitter.
ensure your power adapter complies with this rating.
This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must
• DO NOT place on uneven or unstable work surfaces. Seek
servicing if the casing has been damaged.
be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with
• DO NOT place or drop objects on top and do not shove any
any other antenna or transmitter.
foreign objects into the product.
• DO NOT expose to or use near liquids, rain, or moisture. DO NOT
use the modem during electrical storms.
• DO NOT cover the vents on the product to prevent the system
Radiation Exposure Statement: This equipment complies with FCC
from getting overheated.
radiation exposure limits set forth for an uncontrolled environment.
End users must follow the specific operating instructions for satisfying