Selec SP3-GT35 Operating Instructions

selec
selec
SP3-GT35

SPECIFICATIONS

Display Type
Resolution
Display Size(WxH)mm
Backlight
Brightness Adjustment
Keys
BMP
Font
Application
Upload
System Reserved
Total
External
Slave Port
Master Port
Printer Port
Operation Voltage
Backup Battery
Battery Life
Accuracy
Type
Sound Output
Operation
SP3-GT35
Operating Instructions

FEATURES

Ø 3.5" LCD with Touch
Ø Built in Buzzer
Ø 10 password levels
Ø Modbus protocol
Ø Alarms
Ø Recipe Management
Ø Serial Printing
Ø Data Logging
3.5" TFT LCD (256 color), Resistive Touch Screen
320 x 240 pixels
70.08 x 52.56
LED backlight
Yes (Via Internal MMI)
System key X 1, Function keys X 5
4 MB
4 MB
512 KB
5.5 MB
2 MB
16 MB (System Memory)
Micro SD upto 2 GB (User Memory)
RS232 (MODBUS RTU)
RS485 (MODBUS RTU)
RS232 (LX300 Protocol)
18 - 30VDC
Replaceable 3V CR2032
0
1 year at 25 C
+/- 10 min per Year
Electro Magnetic Buzzer
85 dB at 10cm
Software Programmable
Power Consumption
Operating Temperature
Storage Temperature
Humidity
Certification
Dimensions(WxHxD)mm
Panel Cutout(WxH)mm
Weight

SAFETY PRECAUTIONS

This manual is meant for personnel involved in wiring,
installation, operation and routine maintenance of the
equipment.
All safety related conditions, symbols and instructions
that appear in this operating manual or on the equipment
must be strictly followed to ensure operator and
instrument safety. Any misuse may impair the protection
provided by the equipment.
CAUTION : Read complete instructions prior to
installation and operation of the unit.

INSTALLATION INSTRUCTIONS

CAUTION
1. This equipment, being built-in-type, normally becomes
a part of the main control panel and the terminals do not
remain accessible to the user after installation.
2. Conductors must not come in contact with the internal
circuitry of the equipment else it may lead to a safety
hazard that may endanger life or cause electrical shock
to the operator.
3. Circuit breaker or mains switch must be installed
between the power source and supply terminals to
facilitate power 'ON' or 'OFF' function.
4. The equipment shall not be installed in environmental
conditions other than those specified in this manual.
5. Since this equipment forms part of the main control
panel, its output terminals get connected to the host
equipment. Such equipment shall also comply to EMI /
EMC and safety requirements like CE standard
procedure.
6. Thermal dissipation of equipment is met through
ventilation holes provided on housing of equipment.
Obstruction of these ventilation holes may lead to a
safety hazard.
7. The output terminals shall be loaded strictly as per the
values / range specified by the manufacturer.
4W Max
0 0
0 to 55 C
0 0
- 0 to 8 C
3 0
95% RH
CE, UL (Pending)
99 x 99 x 62.85
92 x 92
275gms

WIRING INSTRUCTIONS

CAUTION
1. Wiring shall be done strictly according to the terminal
layout provided in the operating manual.
2. To eliminate electromagnetic interference use short
wire with adequate ratings and twists of equal size.
3. The power supply connection cable must have a cross
section of 1sq.mm or greater and insulation capacity of
at least 1.5KV.

MECHANICAL INSTALLATION

Outline Dimensions Panel Cutout
(in mm)
Front bezel
Side view
99 53 92
9
For installing the controller
1. Prepare the panel cutout with proper dimensions as
shown above.
2. Remove the clamp from the SMI.
3. Fix the unit into the cutout. Insert the clamp from both
sides and tighten the screws.
CAUTION
The equipment in its installed state must not come in
close proximity to any heating sources, caustic vapors,
oils, steam, or other unwanted process by products.
EMC Guidelines :
1. Use proper input power cables with shortest
connections and twisted type.
2. Layout of connecting cables shall be away from any
internal EMI source.
MAINTENANCE
1. To avoid blockage of ventilation holes, clean the
equipment regularly using a soft cloth.
2. Do not use Isopropyl alcohol or any other organic
Solvents for cleaning.
Doc. Name : OP INST SP3-GT35 OP404-V01(Page 1 of 2)B-B
(in mm)