1. Manuals
  2. Brands
  3. Weatronic Manuals
  4. Remote Control
  5. BAT 60
  6. User manual

Weatronic BAT 60 User Manual

Hide thumbs Also See for BAT 60:
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
Introduction
The Development, production and assembly of all weatronic products is based in Germany. All components are tested with the highest German standards. During the development process reliability
and noise immunity are considered the most.
Please always check
www.weatronic.com
Content:
1.
scope of supply ................................................................................... 2
 
2.
Type approvals .................................................................................... 2
 
2.1.
FCC ................................................................................................. 2
 
2.2.
IC Canada ..................................................................................... 2
 
2.3.
 
2.4.
 
Intended use ................................................................................ 3
2.5.
safety instructions ...................................................................... 3
 
3.
Care instructions ................................................................................. 4
 
4.
General overview ............................................................................... 5
 
5.
Overview about internal electronics .............................................. 6
 
6.
How to open and close the BAT 60 case ....................................... 7
 
7.
open ....................................................................................................... 7
 
8.
 
close ....................................................................................................... 7
9.
Mechanical stick adjustment ........................................................... 8
 
10.
 
11.
 
12.
Mechanical toggle switch adjustment ......................................... 10
 
13.
Hardware extras ............................................................................... 11
 
14.
BAT 60 power supply (10 - 19 Volt) .............................................. 11
 
15.
LED status information ................................................................... 11
 
16.
Transmitter is switched off and charging: .................................. 11
 
17.
Transmitter is switched on: ............................................................ 11
 
18.
How to switch on/off ....................................................................... 12
 
19.
ON ........................................................................................................ 12
 
20.
OFF ....................................................................................................... 12
 
21.
RESET ................................................................................................... 12
 
for more information about the BAT 60. Under the section support videos you will find all the small videos mentioned here in this manual.
"MADE IN GERMANY"
Subject to change - No liability for errors and printing errors - June 2014
®
weatronic
GmbH, Schmiedestraße 2A, D-15745 Wildau, Germany
22.
interface ............................................................................................. 13
 
 
22.1.
The screen .................................................................................. 13
 
 
22.2.
Common interface icons ....................................................... 14
 
 
22.3.
Common interface symbols ................................................... 15
 
 
23.
Calibration of potentiometers and sticks ................................... 16
 
 
 
24.
 
UPDATE ............................................................................................... 16
24.1.
update process of BAT 60 ....................................................... 16
 
 
24.2.
update of weatronic Receivers ............................................. 16
 
 
25.
Binding process ................................................................................. 16
 
 
26.
RC-equipment installations in your model ................................ 16
 
 
27.
How to add new model: ................................................................. 17
 
 
27.1.
1
step: model configuration: ............................................... 17
 
 
 
27.2.
 
2
step: receiver configuration: ........................................... 17
27.3.
3
step: servo configuration graphic ................................... 17
 
 
27.4.
4
step: servo configuration list: .......................................... 17
 
 
28.
weatronic programming philosophy ........................................... 18
 
 
29.
Disclaimer of warranty / damages ............................................... 19
 
 
30.
 
 
 
 
 
 
 
 
 
 
1
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BAT 60 and is the answer not in the manual?

Questions and answers

Related Manuals for Weatronic BAT 60

Summary of Contents for Weatronic BAT 60

  • Page 1: Table Of Contents

    User Manual Introduction The Development, production and assembly of all weatronic products is based in Germany. All components are tested with the highest German standards. During the development process reliability and noise immunity are considered the most. Please always check www.weatronic.com...

  • Page 2: Scope Of Supply

    2. Type approvals Hereby the weatronic ® GmbH declares that the BAT 60 transmitter applies to the requirements and other relevant provisions of the relevant CE directive. A copy of the declaration of conformity and the ETSI and FCC certification can be downloaded at our homepage. (www.weatronic.com) The BAT 60 has been designed, tested and certified according to international standards as follows : 2.1.

  • Page 3: Ce R&Tte

    Article 3.2 Radio ETSI EN300 328 V1.8.1 (2012-06) 2.4. Intended use The weatronic BAT60 transmitter radio control system consists of modular components. The system is designed for exclusive use of remote controlled airplane models, model ships and cars and other models.

  • Page 4: Care Instructions

    Whenever the radio is used in humid air please let it dry properly before switching it on again.  if your BAT 60 got somehow wet inside or outside please switch it off and let it dry before switching it on again. ...

  • Page 5: General Overview

    DC in ( 10 -19 Volt ) USB „1“ micro SD PPM (in/out) mini USB TOP VIEW REAR VIEW Subject to change - No liability for errors and printing errors - June 2014 ® weatronic GmbH, Schmiedestraße 2A, D-15745 Wildau, Germany...

  • Page 6: Overview About Internal Electronics

    The Linux / Display board (called LinDis ) contains the Linux computer which provides the interface to the User! Anyhow it is not necessarily needed to operate the BAT 60. Also there are some more additional smaller PCBs The stick includes 2 hall sensor boards.

  • Page 7: How To Open And Close The Bat 60 Case

     remove the top foam inlay of the aluminum case and place at place the BAT 60 upside down on it.  now use the 2.5 mm Allen key and open all of the 6 M3x20 screws at the bottom ...

  • Page 8: Mechanical Stick Adjustment

     The weatronic stick is a revolutionary design; it allows you to adopt each of the 4 axes to your personal needs. You can adjust the “spring force” and the “feedback characteristics”. Check also the “weatronic-feedback parts“ video at the webpage 10.
  • Page 9 NOT fly and contact our service. Never modify the stick in any way! Subject to change - No liability for errors and printing errors - June 2014 ® weatronic GmbH, Schmiedestraße 2A, D-15745 Wildau, Germany...

  • Page 10: Mechanical Toggle Switch Adjustment

    Also make sure that the cables are not twisted and the connectors are placed right! The length of the cable is 50mm. Subject to change - No liability for errors and printing errors - June 2014 ® weatronic GmbH, Schmiedestraße 2A, D-15745 Wildau, Germany...

  • Page 11: Hardware Extras

    The Wi-Fi dongle will be already as a standard and connects your BAT 60 to any Wi-Fi network.

  • Page 12: How To Switch On/Off

    Press the ON/OFF button for at least 10 seconds, the LED around the button will start to flash rapidly green. Now release the button and the LED will change the color to red. Now you have 3 seconds to press the button again and the BAT 60 will turn off.

  • Page 13: Interface

    The screen The screen of BAT 60 is a capacitive touch screen. This means it recognizes the presence of your finger. Pressing hard on the screen will not improve functionality but reduce lifetime. Furthermore it will not recognize any metal, wood, plastics, etc. If you don’t want to use finger for touch please buy a special pen for capacitive touch screens.

  • Page 14: Common Interface Icons

    Here you get access to In this menu Tabbing Here turn off the model memory, you can have here will Bat 60. Abort on change the current your favorites take you the display or model, add a new one as short link to...

  • Page 15: Common Interface Symbols

    Delete something from list: Reorder a list: Save settings: Abort settings: UNDO Subject to change - No liability for errors and printing errors - June 2014 ® weatronic GmbH, Schmiedestraße 2A, D-15745 Wildau, Germany...

  • Page 16: Calibration Of Potentiometers And Sticks

    BAT 60 Go to our download center and copy the weatronic folder to a formatted USB stick. Insert the USB stick to one of the external USB ports at your BAT 60. Now switch on and wait until the Home screen appears.

  • Page 17: How To Add New Model

     In this menu you tell the BAT 60 everything about the servos used and their location in your plane.  Just add the servos to the control surfaces and set up name, center and limits properly.

  • Page 18: Weatronic Programming Philosophy

    28. weatronic programming philosophy With the weatronic programming style you are no longer limited to channels or predefined and fix structures. The model setup is organized in functions. These could be i.e. aileron, elevator, etc. as you can choose the name yourself.

  • Page 19: Disclaimer Of Warranty / Damages

    As far as legally allowed, the commitment of the weatronic ® GmbH to pay damages, for whatever legal reason, is limited to the invoice value of the directly involved and damage-causing goods of the ®...

Table of Contents