Advertisement
Quick Links
P ass Code & F
1. It should be remained unlock while programming.
2. Please run the door -handing identifying process
(Refer to programming table) before function set up when rst
time installation or default setting restore.
3. Please change default Programming Code (0000) and User
Code (1234) before function set up when rst time operation.
4. LED ashes orange slowly while programming. LED ashes
green twice with 2 long beeps when correct input. LED ashes
red 3 times with 3 beeps when incorrect input.
(Y ou need to wait for 6 seconds or press programming button
when incorrect input, then re-program the system again.)
5. Every programming step should be done in 6 seconds.
6. Y ou can lock/unlock this product by either key or pass code.
Please refer to the following programming table for function
set up.
Remark
1. W e recommend to use alkaline battery in order to stabilize the
power supply .
2. Do not mix alkaline battery with regular zinc-carbon ones or
mixed brands.
3. Do not use any chemical liquid or lubricating oil with additives
to clean the lock body , it will damage the surface or even
Lockey Digital Systems Inc.
mainboard.
4. If there is any problem of the product, please contact your
www.lockeyusa.com
local retailer and send back the product to us for repair or
replacement.
S p e c ific a tio n/F u nc tio n
1.Battery
Four AA （1.5V ）Alkaline batteries.
2.Low Battery
2-1 The batteries should be changed immediately once you see
the LED ashes in red and hear constant beep sounds for
about 10 seconds when press programming button.
2-2 All settings are retained in the memory and will not be
a ected even if the battery is completely dead.
2-3 The lock still can be operated by key even there is a power
outage.
Programming Button
3.LED Indicator
Programming Button is for entering codes, clearing errors and
3-1 LED ashes green once when successful operation.
setting function. It's also lock button.
3-2 LED ashes green twice when successful programming.
Number Buttons
3-3 LED ashes red 3 times when there is an operation error .
Input the pass codes, each pass code is 4-10 digits in length.
3-4 LED ashes red 5 times when codes input error , the operation
Cylinder
will stop for system protection (Refer to 17).
Retract / Extend the latch bolt by key from exterior .
3-5 LED ashes orange 3 times when system has been restored
Washer
to default setting.
Prevent water permeating into lockset.
3-6 LED ashes orange slowly while in programming mode.
Battery Lid
R Button (Reset)
Slide the lid to change the batteries
Restore default setting.
4.Audio Indicator
or restore default setting.
Turn-Piece
4-1 1 beep sound indicates a successful operation.
Battery Holder
Retract/Extend the latch
4-2 2 long beeps indicate a successful programming
Four AA （1.5V ）Alkaline batteries.
bolt from interior .
4-3 3 beeps indicate an operation error .
unction Set up
F unction Programming
Function
Detect Left / Right
Enter PC
Hand Door Installation
Add New UC
Enter PC
Delete An Existing UC
Enter PC
Delete All UC At once
Enter PC
Change PC
Enter PC
Toggle Autolock
Enter PC
On/O
Set Autolock Time
Enter PC
Delay
Toggle Mute On/O
Enter PC
Enable/Disable All UC
Enter PC
Create a disposable
Enter PC
UC
Restore all preset lock
Press "R"
settings
4-4 3 long beeps indicate that system has been restored to
default setting.
4-5 5 beeps when codes input error , the operation will stop for
system protection. (Refer to 17)
4-6 10 rapid beeps indicate the power of battery is low .
5.Programming Code
5-1 The preset Programming Code is 0000. Please delete it and
create your personal code when rst time operation.
5-2 Only one set of Programming Code for function setting.
5-3 Programming Code is only for function setting, you can't
unlock the door by pressing Programming Code.
5-4 Programming code is 4-10 digits in length.
5-5 Programming code can be changed anytime if needed.
6.User Code
6-1 The preset User Code is 1234. Please delete it and create
your personal code when rst time operation.
6-2 Up to 6 sets of User codes can be saved.
6-3 User Code is only for activating the lock, without
programming function.
6-4 User Code is 4-10 digits in length.
6-5 User Code can be deleted or changed anytime if needed.
7.Delete Individual User Code
7-1 User Codes can be deleted individually . You can reset the
same number as code even it's deleted before.
7-2 Y ou should enter Programming code to delete individual
User code.
Steps
Please run the door -handing identifying process before function set up when rst time installation or
Programming
Programming
Press 0
Button
Button
default setting restore.
Programming
Programming
Programming
Press 1
Enter new UC
Up to 6 sets of User Code can be saved. User Code should be 4-10 digits in length.
Button
Button
Button
Enter the UC you
Programming
Programming
Programming
Press 2
Button
Button
Button
want to delete
Auto-locking and K eypad locking function will be invalid when User Codes are deleted.
Programming
Programming
Press 3
Button
Button
The lock can only be operated by key during the time.
Programming
Programming
Programming
Press 4
Enter New PC
Button
Button
Button
The preset delay-time is 30 seconds, you can change the time by following
Programming
Programming
Press 5
Button
Button
instruction. Repeat the steps to cancel the Auto-locking function.
Enter Seconds
Programming
Programming
Programming
Press 6
10-99 seconds delay -time available.
Button
Button
(10~99)
Button
Repeat same steps to turn beeper On/O .
Programming
Programming
Press 7
Button
Button
LED illumination is still functioning when it's in mute. But there will be no any warning alarm.
Auto-locking and K eypad locking function will be invalid when User Codes are disabled. The lock can
Programming
Programming
Press 8
Button
Button
only be operated by key during the time. Repeat the steps to enable the User Codes again.
Enter
Programming
Programming
Programming
Press 9
new disposable
Disposable code will be no longer valid once being used.
Button
Button
Button
UC
Press "R" button for over 5 seconds, the programming will complete after you hear 3 long beeps.
After restore, you need to run the door handing identifying process before other function setting.
8.Delete All User Codes At Once
8-1 All the User Codes can be deleted at once. Y ou can still reset
the same numbers as codes even they're deleted before.
8-2 Auto-locking and K eypad locking function will be invalid
after deleting all User Codes and the lock can only be
operated by key . All the electrical functions will be restored
when recreate new User Codes.
8-3 Y ou need to enter Programming Code to delete all User
Codes.
9.Temporarily Disable All User Codes
9-1 Auto-locking and K eypad locking function will be invalid
when User Codes are temporarily disabled. The lock can only
be operated by key during the time.
9-2 Repeat the programming steps again to restore the User
Codes.
10.Create a Disposable User Code
10-1 Disposable User Code will be no longer valid once being used.
10-2 Y ou can reset same number as Disposal User Code.
10-3 Y ou need to enter Programming Code to create a
Disposable User Code.
11.Restore Preset F actory Code
11-1 Y ou can restore Preset F actory Code by pressing "R" button
on the interior receiver module when you forget Programming
Code or you want to cancel all previous setting.
11-2 After restore, the Programming Code would be 0000; the
User Code would be 1234 again.
Programming Code (PC)
User Code (UC)
Remark
It should be remained
unlock while programming.
12.Unlock the door
15-3 The preset delay-time is 30 seconds; you can adjust the
The door will be unlocked by key or pressing User Code on
15-4 Please repeat the same programming steps to cancel
keypad from outside or by interior turn-piece.
15-5 The system will alarm twice if the latch bolt gets stuck
13.Lock the door
The door will be locked by key or pressing Programming Button
on keypad from outside or by interior turn-piece.
14.Incomplete Door Closing / Opening
14-1 Once the latch bolt is not extended/retracted completely
16.Toggle Mute On/O
and causing a not functional motor operation when it's
16-1 Y ou will hear beep sounds when pressing keypad,
locked by keypad, you'll see LED ash red 3 times (for twice)
programming or operating errors. It can be turned o if
and hear 3 beeps (No alarm when it's in mute). Y
ou need to
needed.
enter User Code to unlock the door for remaining the bolt
16-2 LED Illumination is still functioning when it's in mute. F or
retracted, and press Programming Button to lock the door
there will be no any warning alarm, we suggest not to mute
again.
the beeper if it's not necessary .
14-2 If the latch bolt gets stuck or can't extend/retract
16-3 Motor operating sound cannot be muted.
completely all the time, please check if the strike aligns with
the latch bolt perfectly and adjust the strike to proper
17.Code Protection F unction
position. After long use of the door hinge, the latch bolt
The operation will stop if entering unauthorized codes over 5
might get stuck easily because the door is deformed or
times. The System will re-operate again after 45 sec.
lopsided.
18.Illumination
15.To Activate / Deactivate Auto-Locking F
unction
The LED Keypad will light up when pressing any button for ease
15-1 The door will automatically lock itself within 10~99 seconds
of operating in the dark.
when this function is programmed.
15-2 This function is not preset at the beginning; it can be set if
needed.
USER MANUAL
period you want.
Auto-Locking function when needed.
or not extended/retracted completely .
You need to enter User Code to unlock the door for
remaining the bolt retracted. The auto-locking function will
be restored then.
Advertisement
