Lamptron CU423 Instruction Manual

Lamptron CU423 Instruction Manual
Thank you for choosing LAMPTRON CU423
controller. This controller is compatible with air
cooling and water cooling control.

FEATURES:

Classic Clock Dial design
40W per Channel,4 channels
Voltage,Speed and Temperature display
Manual/Auto Control Mode available
High quality sleeved wires
We recommend that you read the following detailed description
of the installation manual before using the CU423

SPECIFICATION:

Dimension 148.5mm * 42.5mm * 65mm
Power output Up to 40 watts per channel
Control channels 4 Channels
+12V(standard power interface + 5557-2 D
DC Input
shape * 4 p r)
DC Ouput 0 V - 12V DC
Compatible 2510 male head 3 p socket

INSTALLATION:

Installation location:
The CU423 is designed to fit in a 5.25" bay,please use the
included screws to install it within your pc case.(Phillips scre
wdriver needed and not included.)
tuation, please reserve a good connection and linear space.

CONNECTIONS:

1. PWR_IN1 and PWR_IN2: input power supply
Warning: Please be sure connecting PWR-IN1 and PWR-IN2 at
the same time,then the CU423 can work normally！ ！ ！
2. OUT1 ~ OUT4: channel 1 ~ 4 output, it is a standard 3 pin
KF2510 interface.(you can also connect KF2510 4 pin
connector)
3. TEMP1 ~ TEMP4: connect to the temperature sense
4. J2: start boost on/off.

OPERATION:

www.lamptron.com
According to your actual si
①②③④ndicates the channel 1 to 4, ⑤reduce，⑥ increase，
⑦ Speed indicator light， ⑧ temperature indicator light， ⑨ Voltage
indicator light

SETTING:

Power on over 2 seconds to enter the display mode.At same
time,each channel can be setup.
Automatic mode is ruuning at least 4.5 V - 12 V
In Auto Mode,the indicator lights are all lighted up(Voltage,
Speed,Temperature).
1, CU423 can be ruuning in Manul/Auto Mode.In Auto Mode,user
can not make any changes.
2, the left side of button for reducing, the right side of the button for
increasing;
Short push each button means switching from Voltage,Speed
and Temperature
Long Push each button over 3 second means switching
between Manul/Auto Mode.
3, CU423 start boost function ON
CU423 start boost function OFF
Setup Manual/Auto Mode:
CU423 setup as manual mode originally.
Long press the button for 3 seconds to switch between
Manul/Auto mode
Once choosed Auto Mode,3 indicators LEDs(Voltage,Speed
and Temperature) all lighted up to show Auto mode is ON.
Once choosed Manual
LEDs(Voltage,Speed and Temperature) all lighted up to show Auto
mode is OFF.
Manual mode:
CU423 defaults as Speed indicator is ON
Short press the button to switch to the voltage indicator ON,
press button on the right side is inceasing,press button on the left
side is reducing.
CU423 have memory function.Once power off,CU423 can running
back to last time users' setup.
Automatic mode:
CU423 automatic mode means the target temperature is 45
the minimum voltage is 4.5V,the maximum voltage of 12V.Once the
temperature is above 60 .CU423
℃
(Warning: automatic mode needs to connect the corresponding
channel of thermal sensors.)

Alarm function:

When the voltage reaches 7 v and above, and no speed at the
same time, then alarming and speed indicator flashing.
When the temperature reached 85 ℃ and above, then alarming and
temperature indicator flashing
We hope you enjoy Lamptron CU423 and it
serves your projects well.if you think any aspect of
the CU423 can be improved or if you are willing to
share your creative ideas with us, you are more than
welcomed to contact
(info@lamptron.com).We are always happy to hear
from you !
info@lamptron.com
Mode, 3 indicators
will works in full power
us through our email
,
℃