Electronics Line EL5845 Installation Instructions

Wireless 1 & 2-Way PIR / PET
Detector
Models: EL5845 / EL5845PI
Installation Instructions
Description
The EL4845 / EL5845PI is a battery powered 1 & 2‐Way
wireless PIR / PET detector that is compatible with
Electronics Line 2‐Way security systems.
Features include:

15m coverage (wide angle) with 90° field‐of‐view

Installation height 2.4m

1‐Way / 2‐Way RF option (DIP switch selectable)

2 long‐life lithium batteries for extended battery life

Frequency: 868Mhz or 433Mhz

PET Immunity option (45Kg animals)
Installation
Step1: Selecting a Mounting Location
Select the mounting location for best coverage of the area
that is to be protected (see Preliminary Considerations and
Coverage Patterns).
Step 2: Registering the Detector in the
System
The detector must identify itself to the system's receiver
(control panel) during the registration process.
1. Set the system to registration mode.
2. Go to the main menu and select
[9] Programming > [1] Devices > [1] Zones.
3. Select a zone and press ʹʹ. The system enters into
Learn mode.
4. Unlock and remove the mounting bracket from
the detector (see Figure 1 and Figure 3).
5. Set the detector DIP switch settings (see Figure 3
and DIP Switch Settings).
6. Insert the supplied batteries into the battery
holders paying attention to the correct polarity or
remove the plastic protector strip if the batteries
are already in place (see Figure 3).
The detector sends a transmission to the system. If
the transmission is successfully received by the
system it plays a confirmation sound.
If no confirmation sound is heard, send another
transmission by pressing and releasing the tamper
switch of the device (see Figure 3).
Once the detector is successfully registered the
system display shows: Save?
7. Press  to confirm and continue entering other
parameters for the chosen device (see Parameter
Configuration).
Step 4: Mounting the Detector
The detector must be tested on the exact mounting
position before permanently mounting.
1. Open the knockout holes of the mounting bracket,
and use them as a template for mounting (see
Figure 2).
For Pet friendly model: In order to optimize pet
immunity, always mount the detector vertically at a right
angle to the floor. Make sure that an animal cannot get
above the height of 1.5m (5ʹ) by climbing on furniture,
shelving or stairs.
2. Once the bracket is installed, slide and lock the
detector onto the mounting bracket.
3. Perform a Walk Test (see Performing a Walk Test).
4. Insert and fasten screw into the hole located at the
bottom of the detector to lock the detector to the
mounting bracket (see Figure 4).
Step 5: Performing a Walk Test
The detector needs approximately 90 seconds to warm
up after applying power.
Go to the systems main menu and select [7] Service > [6]
Walk Test and press ʹ.
During Walk Test mode, walk through the entire field of
view of the detector and confirm that the LED activates
and deactivates accordingly (see LED Indication).
Verify that the system receives the signals.
NOTE: Wait for ten seconds, after each detection, before
continuing the test.
After completing the walk test, reset the system to
Normal mode.
LED Indication
Status Indication
On (in alarm mode) Detection alarm
Blinking twice (in Low battery
alarm mode):
Blinking four times (in Successful registration
learning mode)
DIP Switch Settings
1‐Way parameters can be modified from the DIP switch.
DIP Function Option
1 1‐Way / OFF (1‐Way /
2‐Way ON (2‐Way)*
2 LED OFF / ON*
3 Sensitivity OFF (Low, 3m)* /
ON (High, 6m)
4 Normal / OFF (Normal, 2,5 min)* /
Walk Test ON (Walk Test)
* = Default
Parameter Configuration
2‐Way parameters can be modified from the system.
Go to the main menu and select [9] Programming > [1]
Devices > [1] Zones > [11].Sensor Par.
LED: Enable* / Disable
PIR Sensitivity: Low* / High
Alarm Delay: 1‐20 minutes (3 mins.*)
* = default
For additional information refer to the System Installer
Manual.
Diagnostics
You can perform diagnostic tests on your detector using
the system. Diagnostics includes testing the detector
battery status and the communication between the
detector and the system.
For additional information refer to the System Installer
Manual.
Battery Replacement
1. Unlock and slide the detector from the mounting
bracket.
2. Replace the batteries paying attention to the
correct polarity.
3. Slide and lock the detector to the mounting
bracket.
CAUTION – Risk of explosion if battery is replaced by
an incorrect type. Dispose of used batteries according to
local regulations.
Specifications
Electrical
Battery Type: 2 x CR 123, 3V Lithium
Battery Life: 2 batteries – 3 year typical
lifetime
Current 58 A standby;
Consumption: 200 mA max.
Supervision 0‐255 minutes
Transmission:
RF transmitting 868MHz, 433MHz ‐ models
frequencies: EL5845 and EL5845PI
Optical
Filtering: White Light Protection
Pet friendly: Up to a 45 kg animal
immunity (pet model)
Physical
Size (L x W x D): 120 x 65 x 35 mm (4.7 x 2.6 x
1.8 in)
Weight: 100 grams (3.52 oz.)
Environmental
RF Immunity: According to EN50130‐4
Operating ‐10C a 55C (14F a 140F)
Temperature:
Storage ‐20C a 60C (‐4F a 140F)
Temperature:
Preliminary Considerations
Do not install outside Do not install near
windows
Do not install near Do not install near
vents (air, heat, or AC) ceiling fans
Do not install in Do not install in direct
sunlight
extreme temperatures
Ok for sites with small pets
PIR Coverage Patterns
PIR Model
ft. m
PIR - SIDE VIEW
10 3
2
5
1
0
m
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0 5 10 15 20 25 30 35 40
45 50 ft
ft m
PIR - TOP VIEW
30 9
8
25
7
20 6
5
15
4
10 3
2
5
1
0 0
1
5
2
10 3
4
15
5
20 6
7
25
8
30 9
m
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0 5 10 15 20 25 30 35 40 45 50 ft
PET Model
ft m PIR Pet - SIDE VIEW
10 3
2
5
1
0
0 1 2 3 4 5 6 7 8 9 10 11 12 m
0 5 10 15 20 25 30 35 40 ft
ft m PIR Pet - TOP VIEW
8
25
7
20 6
5
15
4
10 3
2
5
1
0 0
1
5
2
10 3
4
15
5
20 6
7
25
8
0 1 2 3 4 5 6 7 8 9 10 11 12
30 9
0 5 10 15 20 25 30 35 40