Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MasterCraft 058-7713-6
Summary of Contents for MasterCraft 058-7713-6
- Page 1 INSTRUCTION MANUAL AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
- Page 2 QUICK START GUIDE TECHNICAL SPECIFICATIONS SAFETY GUIDELINES 4–9 KEY PARTS DIAGRAM IMPORTANT INFORMATION 11–13 OPERATING INSTRUCTIONS 14–15 MAINTENANCE 16–17 TROUBLESHOOTING 18–19 EXPLODED VIEW PARTS LIST WARRANTY 22–23 AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
-
Page 4: Personal Safety
PERSONAL SAFETY These precautions are intended for the personal safety of the user and others working with the user. Please take time to read and understand them. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6... -
Page 5: Safety Guidelines
Disconnect the compressor from the power source before servicing. Compressor must be grounded. Do not use grounding adaptors. Risk of personal injury: Do not direct compressed air from the air hose • toward the user or other personnel. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6... - Page 6 Drain water from tank after each use. Do not weld or repair tank. Relieve all pressure in the hose before removing or attaching accessories. MC-OM-22 AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
- Page 7 Do not operate the compressor on a rooftop or in an elevated position that could allow the unit to fall or be tipped over. • Always replace a damaged gauge before operating the unit again. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
- Page 8 Do not use the tool near or below the freezing temperatures, as doing so may cause tool failure. • Do not store the tool in a freezing environment to prevent ice formation on the operating valves of the tool, as doing may cause tool failure. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
- Page 9 Note: Recycle unwanted materials rather than disposing of them as waste. Sort the tools, hoses, and package in specific categories and take to the local recycling centre, or dispose of them in an environmentally safe way. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
- Page 10 MC-587713-02 Description Description Air inlet plug Safety lock Trigger Chuck screw AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
-
Page 11: General Use
GUIDELINES FOR PROPER USE AND OPERATION ® Be sure to use a proper air compressor with Mastercraft air-powered tools. The compressor should be able to supply a minimal air delivery of 2.2 SCFM @ 90 PSI to ensure the compressor can run continuously with the Mastercraft Air-powered Right Angle Die Grinder. -
Page 12: Air System
Verify that all connections in the air supply system are sealed in order to prevent air leakage. MC-587713-03 Description Description ® Mastercraft Air-powered Right Angle Die Filter Grinder Air hose Cut-off valve Lubricator Air compressor Regulator (0 to 8.5 bar) AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6... - Page 13 (carbon dioxide), or any other combustible, or bottled gas to power this tool. • Do not use this tool in the presence of any flammable liquids or gases. Failure to comply could result in serious injury or loss of life. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
-
Page 14: Loading And Operation
2. Use the two wrenches (1) to loosen the chuck (2). Insert a suitable grinding fig B accessory into chuck, and firmly retighten the chuck to lock the grinding accessory in place using the wrenches (fig B) MC-587713-05 AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6... - Page 15 Potential hazard that could result in serious injury or loss of life. • Hold the tool firmly with both hands. Always point abrasive material away from you while operating the tool. Failure to comply could result in serious injury or loss of life. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
-
Page 16: Maintenance
6 drops of pneumatic tool oil into the air inlet before each work day or after every 2 hours of continuous use, depending on the characteristics of the workpiece used. MC-587713-09 AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6... - Page 17 Disconnect the tool from the air supply, clean the tool, and store the tool in a safe, dry, childproof location. Note: When temperatures are below freezing, maintain the tool in a warm condition using any safe, convenient method. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
-
Page 18: Troubleshooting
3. Operate the tool in forward and/or reverse air flows slightly rotations within short duration. from exhaust. Repeat the above steps as per requirements. If this fails, return the tool to the service center. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6... - Page 19 5. If tool remains jammed, return to service center Tool does not shut O-rings or throttle valve is dislodged 1. Replace O-rings or return to service center. off. from valve seat . Note: For further repair information, please call 1-800-689-9928. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
- Page 20 31 32 MC-587713-08 AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
- Page 21 O-ring 7 X 2 Washer O-ring 11 X 2 Cylinder Screw cap Rotor Wrench I Rotor blade Wrench II If any parts are missing or damaged, or if you have any questions, please call 1-800-689-9928. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
- Page 22 This warranty will not apply where damage is caused by repairs made or attempted by others (i.e., persons not authorized by the manufacturer). This warranty will not apply to any product that was sold to the original purchaser as a reconditioned or refurbished product (unless otherwise specified in writing). AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
-
Page 23: Additional Limitations
This warranty gives you specific legal rights, and you may have other rights, which may vary from province to province. The provisions contained in this warranty are not intended to limit, modify, take away from, disclaim, or exclude any statutory warranties set forth in any applicable provincial or federal legislation. AIR-POWERED RIGHT ANGLE DIE GRINDER 058-7713-6...
Need help?
Do you have a question about the 058-7713-6 and is the answer not in the manual?
Questions and answers