Table of Contents
Advertisement
Analysentechnik
Moisture detector controllers
Type FF-
Installation and Operation Instructions
Original instructions
BE410002
Bühler Technologies GmbH, Harkortstr. 29, D-40880 Ratingen
09/2017
Tel. +49 (0) 21 02 / 49 89-0, Fax: +49 (0) 21 02 / 49 89-20
E-Mail: analyse@buehler-technologies.com
Internet: www.buehler-technologies.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Buhler FF-HM-230
Summary of Contents for Buhler FF-HM-230
- Page 1 Analysentechnik Moisture detector controllers Type FF- Installation and Operation Instructions Original instructions BE410002 Bühler Technologies GmbH, Harkortstr. 29, D-40880 Ratingen 09/2017 Tel. +49 (0) 21 02 / 49 89-0, Fax: +49 (0) 21 02 / 49 89-20 E-Mail: analyse@buehler-technologies.com Internet: www.buehler-technologies.com...
- Page 2 Bühler Technologies GmbH, Harkortstr. 29, D-40880 Ratingen Tel. +49 (0) 21 02 / 49 89-0, Fax: +49 (0) 21 02 / 49 89-20 Internet: www.buehler-technologies.com E-Mail: analyse@buehler-technologies.com Read this instruction carefully prior to installation and/or use. Pay at- tention particularly to all advises and safety instructions to prevent in- juries.
-
Page 3: Table Of Contents
Type FF- Contents Introduction............................................. 2 Intended use ......................................... 2 Types ............................................ 2 Contents.......................................... 2 Safety instructions......................................... 3 Important advice ......................................... 3 General hazard warnings .................................... 4 Transport and storage ........................................ 5 4 Installation and connection ...................................... 6 Mounting.......................................... 6 4.1.1 Mounting of moisture detector and adapter .......................... 6 4.1.2 Mounting of detector-controller.............................. -
Page 4: Introduction
FF-40 moisture detector with cable break detection, max. pressure 40 bar Type G flowcell in PVDF Type S flowcell in stainless steel Controllers Voltage Connectible moisture detectors FF-HM-230 for rail mounting 230/115 V AC for one FF-3-N moisture detector or FF-40 FF-HM-24 for rail mounting... -
Page 5: Safety Instructions
Type FF- 2 Safety instructions 2.1 Important advice Operation of the device is only valid if: – the product is used under the conditions described in the installation- and operation instruction, the intended application according to the type plate and the intended use. In case of unauthorized modifications done by the user Bühler Technolo- gies GmbH can not be held responsible for any damage, –... -
Page 6: General Hazard Warnings
Type FF- 2.2 General hazard warnings The equipment must be installed by a professional familiar with the safety requirements and risks. Be sure to observe the safety regulations and generally applicable rules of technology relevant for the installation site. Prevent malfunctions and avoid personal injuries and property damage. -
Page 7: Transport And Storage
Type FF- 3 Transport and storage The device should be only transported in the original case or in appropriate packing. If the device is not used for some time, protect it against heat and humidity. Store the device in a roofed, dry, and dust free room. -
Page 8: Installation And Connection
Type FF- 4 Installation and connection 4.1 Mounting 4.1.1 Mounting of moisture detector and adapter The flow adapter is equipped with internal threading, G1/4 or NPT1/4 (flow adaptor marked with NPT), for the gas connections and G1/4 for the moisture sensor. The drawing you find on the backside of the attached data sheet. As well the fittings as the moisture detector must be used with Teflon sealing or an O-ring to assure proper sealing of the sample stream. -
Page 9: Controller Type Ff-19
The type FF-HM-230 is suitable for 230 V AC and 115 V AC. The jumpers are factory set to 230 V AC. To change it to 115 V AC discon- nect the jumper between terminals 9-10 and set jumpers to terminals 8-9 and 10-11. The power supply is connected to terminals 12-13 (PE is 7). -
Page 10: Controller Type Ff
Type FF- NOTICE To prevent malfunction, the wires to the reset switch have to be shielded! 4.2.3 Controller type FF-..-U Note the drawing 41/065-07-4. After opening the housing you will see the switch for the voltage adjustment next to the fuses, which must first be set to your voltage. -
Page 11: Operation And Control
Type FF- 5 Operation and control NOTICE The device must not be operated beyond its specifications. It might be necessary to adjust the position of the humidity sensor in strongly fluctuating ambient or component temperatures in order to ensure the necessary tightness in the system. 5.1 Adjusting the sensitivity NOTICE If the moisture detector controller works in combination with a sample gas cooler, please... -
Page 12: Maintenance
– With a matching tool press the lashes on the sides away from the sides carefully. Take the front away from the housing. – Below the upper PCB there are the fuses (one for the FF-HM-24, two for the FF-HM-230). -
Page 13: Service And Repair
40 11 000 Type G flowcell (PVDF) 40 11 000I Type NPT1/4 flowcell (PVDF) 40 11 005 Type S flowcell (stainless steel) 41 11 020 Controller FF-HM-230 41 11 030 Controller FF-HM-24 41 11 017 Controller FF-1-U 41 11 015 Controller FF-3-U... -
Page 14: Disposal
Type FF- 8 Disposal Dispose of parts so as not to endanger the health or environment. Follow the laws in the country of use for disposing of elec- tronic components and devices during disposal. Bühler Technologies GmbH BE410002 ◦ 09/2017... -
Page 15: Appendices
3...50 °C) (Only when using ER-145/A/Ex, refer to operating instructions) Adapters Type G Type S Material: PVDF 1.4571 Controllers FF-HM-230 FF-HM 24 FF-19 FF-x-U ER-145/A/Ex Supply voltage: 230/115 V AC 24 V DC ±10 % 24 V DC ±10 %... - Page 16 Type FF- FF-HM230 FF-19 FF-x-U ER-145/A/Ex 22.5 Power Reset Moisture alarm Cable break alarm Sensitivity controller Housing depth 109 Housing depth 81 Housing depth 170 Housing depth 120 Bühler Technologies GmbH BE410002 ◦ 09/2017...
-
Page 17: Attached Documents
Type FF- 10 Attached documents – Connections diagrams: 47/075-06-4 (type FF-19) 41/073-01-4 (type FF-HM 230) 41/074-01-4 (type FF-HM-24) 41/065-07-4 (types FF-..-U) – Declaration of Conformity KX410001 – RMA - Decontamination Statement BE410002 ◦ 09/2017 Bühler Technologies GmbH... - Page 23 RMA - Dekontaminierungserklärung RMA - Decontamination Statement DE/EN Gültig ab / valid since: 2014/11/01 Revision / Revision 1 ersetzt Rev. / replaces Rev. 0 Um eine schnelle und reibungslose Bearbeitung Ihres Anlie- Please complete this return form to ensure your claim is gens zu erreichen, füllen Sie bitte diesen Rücksendeschein processed quickly and efficiently.
- Page 24 RMA - Dekontaminierungserklärung RMA - Decontamination Statement DE/EN Gültig ab / valid since: 2014/11/01 Revision / Revision 1 ersetzt Rev. / replaces Rev. 0 Bitte füllen Sie diese Dekontaminierungserklärung für jedes Please complete this decontamination statement for each einzelne Gerät aus. individual item Gerät / Device RMA-Nr /...
Need help?
Do you have a question about the FF-HM-230 and is the answer not in the manual?
Questions and answers