Advertisement
Quick Links
Curtain PIR Motion Sensor (CIR-S1)
P
P
a
a
r
r
t
t
s
s
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
1. LED indicator
The LED Indicator is under the front cover and is only visible
when turned on.
2. Battery Insulator
3. Tamper Switch
The Tamper switch protects the PIR from unauthorized cover
opening or removal from mounted surface
4. Learn/Test Button
Press the button to transmit a learn/test code and enter Test
mode for 3 minutes.
5. Supervision Enable/Disable Jumper Switch
(JP2)
High/Low Sensitivity Jumper Switch (JP3)
6.
P
a
c
k
a
g
e
C
o
n
t
e
n
t
P
a
c
k
a
g
e
C
o
n
t
e
n
t
1 x PIR Sensor
2 x wall plugs and screws
1 x CR123A 3V lithium battery(pre-installed)
Supervision Enable/Disable Jumper Switch (JP2)
Jumper On
The jumper link is inserted
connecting the two pins
If enabled, the PIR sensor will transmit supervision signal to
Control Panel periodically for the sensor to monitor PIR sensor
condition.
Jumper set to ON = supervision function is Disabled
Jumper set to OFF = supervision function is Enabled (Default)
High/Low Sensitivity Jumper Switch (JP3)
Jumper On
The jumper link is inserted
connecting the two pins
Jumper set to ON = PIR sensitivity is set to High
Jumper set to OFF= PIR sensitivity is set to Low (Default)
L
e
a
L
e
a
Put the Control Panel into learning mode, then press the learn
button to transmit learn code. Please refer to Control Panel
manual for to complete the learning process.
Jumper Off
if the jumper link is removed
or parked on one pin.
Jumper Off
if the jumper link is removed
or parked on one pin.
r
n
i
n
g
r
n
i
n
g
D
e
t
e
c
t
i
o
n
C
D
e
t
e
c
t
i
o
n
C
When mounted vertically, the PIR has a horizontal detection
coverage of 10° and vertical detection coverage of 110° to the
front. The PIR will only be activated by movement across the 10°
horizontal coverage.
Top View
There are 3 ways to mount the PIR for different coverage
according to different scenarios
V
V
e
e
r
r
t
t
i
i
c
c
a
a
l
l
W
W
a
a
l
l
l
l
M
M
o
o
u
u
n
n
t
t
Mount the PIR on the wall vertically to protect against anyone
attempting to move across the detection area
When mounted at 1.4~1.7 meter height, the PIR has a detection
range of 10 meters against horizontal movement. Avoid mounting
outside suggested height or the detection range may be reduced.
H
o
r
i
z
o
n
t
a
l
W
a
l
l
M
o
u
n
t
H
o
r
i
z
o
n
t
a
l
W
a
l
l
M
o
u
n
t
Turn the PIR horizontally and mount on wall to protect against
vertical movement across the detection area. This practice is
usually used to protect against intruder from sky light and roof
hatch.
When mounted horizontally, the PIR has a detection range of 5
meters against vertically movement only. It will NOT be able to
o
v
e
r
a
g
e
o
v
e
r
a
g
e
Side View
Advertisement
Related Manuals for Blaupunkt CIR-S1
Summary of Contents for Blaupunkt CIR-S1
- Page 1 Curtain PIR Motion Sensor (CIR-S1) 1. LED indicator When mounted vertically, the PIR has a horizontal detection The LED Indicator is under the front cover and is only visible when turned on. coverage of 10° and vertical detection coverage of 110° to the 2.
- Page 2 detect horizontal movement. another minute. In this way continuous movement in front of a PIR will not unduly exhaust the battery. Press the Test Button to enter Test mode for 3 minutes. Sleep timer will be disabled under Test mode, and the LED indicator will flash every time a movement is detected.