KT&C KPC-HDB230M Operation Manual

M1 7 2-H D B 23 0- 00 2
HD C CT V
D ig i ta l V i de o Cam er a
OPERATION M ANUAL
Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow these instructions.
INS TA L L AT I O N
M o nit or C o nn ec t io n
BNC Female
(HD-SDI Jack)
DC12V IN (Black)
BNC Female (2'nd Video)
Camera
RCA Jack
(OSD Key Jack)
When you install the camera, please glue up the end of
cable to keep it stable in order to protect the camera from
the humidity problems.
* Remote Control - Circuit Diagram (Option)
Function
SW1: Menu OSD Menu on / off, Selection.
SW2: Up OSD Menu up.
SW3: Down OSD Menu Down.
SW4: Left OSD Menu Left.
SW5: Right OSD Menu Right.
CAUT ION S
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
WARNING -
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
Caution -
Any changes or modifications in construction of this devies which are not
expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
CAUTION
1. A regulated DC12V 300mA power supply is recommended for use with this
camera for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When an unregulated power supply is applied, the product warranty will be roid.
2. It is recommended that the camera be used with a monitor that has a CCTV
quality 75Ω video impedance level. If your monitor is switched to high impedance
then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal
componets. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reflective light, which
may cause smear on the picture and possible damage to the image sensor.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a main socket-outlet with a protective
earth connection.
RS-485 Type
HD SDI IN
Monitor
DC12V Power Supply
Camera
5Key Remote Control
When you install the camera, please glue up the end of
(Option)
cable to keep it stable in order to protect the camera from
the humidity problems.
DIME N SI ON S
Board Lens
(Only IP67)
Board Lens
WEEE
(Waste Electrical & Electronic Equipment)
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from
other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how
they can take item for environmentally safe recycling.
Business users should contact their supplier and check the terms
and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for
disposal.
C AU TION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER(OR BACK). NO USER SERVICING TO QUALIFED SERVICE
PERSONNEL.
This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient mangnitude to constitute
a risk of electric shock.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction
in the literature accompanying the appliance.
HD SDI IN
BNC Female
(HD-SDI Jack)
DC12V Power Supply
DC12V IN (Black)
PC
RS-485
Connection
Unit(mm)
Pinhole Lens
16.8
77.5
4
1/4"-20UNC
68.6 4
C O M PO N EN T S
HD CCTV Camera
Screw - 3ea
Option - Remote Control (OSD Key)
1M or 35M(Maximum working distance.)
M O U N T P O SI TI O N
S PE C I F I C ATI O N
Image Device 2.43 Mega Pixel, 1/2.9" Exmor SONY CMOS
HD-SDI: 1080p@30, 1080p@25, 720p@60,
Video output mode
Monitor
Effective Pixels
Unit cell size
S/N Ratio
Minimum Illumination 0.9Lux(F2.5, DSS Off) / 0.1Lux (DSS On)
Video Output
Lens
Shutter speed
D-WDR / BLC
3DNR
Controllable Max Gain
White Balance
Digital Zoom Ratio
Digital Slow Shutter
Privacy Masking
Day & Night
OSD
Operating Temperature
4 Storage Temperature
61.5
Power Consumption
Dimensions (mm) 23.0(Ø) x 77.5(WaterProof Cap Housing only)
28.6 Weight
3-Ф3.2
IP Rating
Specifications and designs are subject to change for improving the func-
tionality of this product without notice.
Mounting Bracket
Operation Manual
720p@50
TV Out: NTSC / PAL selectable
1984 (H) x 1105 (V)
2.8um (H) x 2.8um (V)
More than 50dB
HD-SDI / 1.0 Vp-p Composite ( 75Ω ).
Board Lens, Pinhole Lens
Auto / Manual selectable
OFF / BLC / D-WDR
OFF / LOW / MIDDLE / HIGH
23 dB
AUTO / AUTOext / PUSH / MANUAL
1X ~ 20X
OFF, X2 ~ X8
Zone 16 ea , On / Off
Digital Day & Night
Remote Control /
RS-485 Remote Control (RS-485)
14°F~112°F (-10°C~+50°C)
-4°F~158°F (-20°C~+70°C)
DC12V (±10%), Max. 110 mA
Approx. 90g
IP67 (WaterProof Cap Housing only)