Related Manuals for Eurotech ISIS
Summary of Contents for Eurotech ISIS
- Page 1 USER MANUAL ISIS Development Kit PC/104-Plus single board computer Rev. 3.0 - July 2009 - ETH_ISIS-DEVKIT_USM DIGITAL TECHNOLOGIES FOR A BETTER WORLD www.eurotech.com...
- Page 2 The warranty on all third party manufactured products utilised by Eurotech is limited to 1 year. Eurotech will make all reasonable effort to repair the product or replace it with an identical variant. Eurotech reserves the right to replace the returned product with an alternative variant or an equivalent fit, form and functional product.
-
Page 3: Table Of Contents
Contents Contents Handling your board safely .......................4 Conventions..........................4 Introduction..........................5 ISIS Development Kit features ....................7 CPU module .........................7 ISIS PC/104+ carrier board ..................7 ISIS-Breakout board .....................8 ISIS-HDA board ......................8 Display set (LCD variant only) ..................8 Software specification.......................9 Operating system support ....................9 Drivers ..........................9... -
Page 4: Handling Your Board Safely
The battery is inserted in a socket and can be replaced with a 3.0V Lithium CR2032 Coin Cell. Packaging Please ensure that, should a board need to be returned to Eurotech, it is adequately packed, preferably in the original packing material. Electromagnetic compatibility (EMC) The ISIS is classified as a component with regard to the European Community EMC regulations and it is the user’s responsibility to ensure that systems using the board are... -
Page 5: Introduction
• ISIS NO-LCD DevKit, assembled with the perspex base only (No display set). Both variants of the DevKit contain the ISIS carrier board, the CPU module and its heat sink, an I/O breakout board and an audio board. The ISIS development kit supports the following features: •... - Page 6 ISIS Dev Kit user manual ISIS development kit Issue C...
-
Page 7: Isis Development Kit Features
ISIS Development Kit features ISIS Development Kit features CPU module Processor • Intel ATOM processor (13mmx14mm BGA): Z530, 1.6GHz, TDP: 2W, or Z510, 1.1GHz, TDP: 2W. Chipset • Intel System Controller Hub (22mmx22mm BGA): US15W, TDP: 2.3W. System memory •... -
Page 8: Isis-Breakout Board
ISIS Dev Kit user manual ISIS-Breakout board Power supply • +12V operation (Power brick supply input). • On/Off button. • Power LED’s. • On-board coin cell battery for RTC backup. Serial port • One full RS-232 port (COM1). Interfaced to the TSC1 by default (LCD variant only). -
Page 9: Software Specification
All system components have drivers available for Windows XP and Linux. Refer to the relevant Software manual for more information. BIOS The CPU module incorporates a custom system BIOS developed by Eurotech which is based on the InsydeH2O core from Insyde Software, www.insydesw.com/products/products-efi-h2o.htm. -
Page 10: Hardware Specification
ISIS Dev Kit user manual Hardware specification What’s in the Kit? • Perspex base with the ISIS, Breakout and Audio boards mounted on it. • Perspex panel with the 8.4” flat panel display, inverter and TSC1 mounted on it (LCD variant only). -
Page 11: Expansion Buses
The CPU module PCI Express port 2 is connected directly to the PCIe Mini Card socket on the ISIS. USB 2.0 and SMBus interfaces are also routed to the PCIe Mini Card socket. The PCIe Mini Card socket supports a SIM card socket mounted onto the ISIS board. -
Page 12: Sdio/Mmc Socket
ISIS Dev Kit user manual SDIO/MMC socket An SDIO socket is provided on the ISIS using the CPU module 4 bit wide access port 1. The SDIO card interface offers great flexibility, including the ability to use the SD socket for data storage and I/O cards such as Bluetooth and WiFi. -
Page 13: Ide Support
1 directly to the upper SUBD9 male connector on the ISIS breakout. A suitable cable is provided in the cable kit to do so. Serial port 2 is a software selectable RS232/485/422 port and is accessible on a standard SUBD9 male connector. -
Page 14: Power Requirements
The typical power consumption of the development kit system with no extra device/add- on card is less than 20W. Although the ISIS does not use the +12V rail, it is routed to PC/104-Plus and PC/104 connectors and can be used by devices or modules stacked onto the ISIS module. It is also connected to the 4-way PC type power connector to provide power to an optional hard-drive or DVD/CD-drive. -
Page 15: Connectors And Jumpers
Connectors and jumpers Connectors and jumpers ISIS-Breakout The following diagrams show the location of the connectors and jumpers on the ISIS- Breakout. Top view J11 J13 Side view Reset J2 (top) J3 (top) J5 (ETH) J6 (VGA) On/Off IDE access... - Page 16 ISIS Dev Kit user manual Summary of connectors and jumpers The following table lists the connectors on the ISIS-Breakout: Connector Function Connector details in section DC_IN J1 – DC_IN, page COM1/COM2 J2 – COM1/COM2, page USB0/USB1 J3 – USB0/USB1, page...
- Page 17 Connectors and jumpers Connectors There are 15 connectors on the ISIS-Breakout; the use of each one is explained below. J1 – DC_IN Socket : 2.1mm DC Jack socket. Mating plug : 2.1mm DC Jack plug. Signal name Positive terminal (+12V)
- Page 18 ISIS Dev Kit user manual J4 – Multifunction and VGA Connector : FCI Minitek 98464-G61-18ULF, 18-way, 2mm (.0787"), shrouded header. Mating housing : FCI Minitek 90311-018LF. Crimps : FCI Minitek 77138-201LF. Mating IDC receptacle : FCI Minitek 89947-718LF. Signal name...
- Page 19 Connectors and jumpers USB4/USB5 Signal name Signal name (top) (bottom) +V5_USB45 +V5_USB45 USB_D4- USB_D5- USB_D4+ USB_D5+ J6 – PS/2 mouse and keyboard and VGA Connector : Stacked HD15 VGA and dual 6-pin Mini-DIN PS/2 connectors. Mating plugs : PS/2 and VGA plugs. Signal name Signal name +V5F...
- Page 20 ISIS Dev Kit user manual J7 – CDROM/HDD power Connector : TYCO 770997-1 power header. Mating housing : TYCO 1-480426-0. Crimps : TYCO 163305-2. Signal name +12V J7 provides output power only. Do not connect to an input power source.
- Page 21 Connectors and jumpers J10 – External On/Off Connector : FCI Dubox 76384-402LF, 2-way, 2.54mm (0.1") header. Mating Housing : FCI Dubox 65240-002LF. Crimps : FCI 76357-401LF. Signal name PWRBTN# J11 – TSC1 Power Connector : MOLEX KK 0022057028, 2-way, 2.54mm (0.1") header. Mating Housing : MOLEX KK 0022012025.
- Page 22 ISIS Dev Kit user manual J17 – COM1 and COM2 Connector : FCI Minitek 98464-G61-18ULF, 18-way, 2mm (.0787"), shrouded header. Mating housing : FCI Minitek 90311-018LF. Crimps : FCI Minitek 77138-201LF. Mating Receptacle : FCI Minitek 89947-718LF. Signal name Signal name...
- Page 23 Connectors and jumpers Jumpers There are three jumpers on the ISIS-Breakout; the use of each one is explained below. JP1 – BAT-EN JP1 function table: Position Function Open Battery is disconnected Closed (default) Battery is connected JP2 – BEEP-EN JP2 function table:...
-
Page 24: Isis-Hda Board
ISIS-HDA board The following diagram shows the location of the connectors on the ISIS-HDA board. Top view Connectors There are four connectors on the ISIS-HDA board; the use of each one is explained below. J1 – LINE IN/SURR Socket : 3.5mm stereo jack. - Page 25 Connectors and jumpers J3 – LINE OUT Socket : 3.5mm stereo jack. Mating plug : 3.5mm stereo plug. Signal name - 2.0 mode Signal name - 5.1 mode Line out left Front surround left Ring Line out right Front surround right Sleeve Ground Ground...
-
Page 26: Appendix A - Reference Information
ISIS Dev Kit user manual Appendix A – Reference information Product information Product notices, updated drivers, support material: www.eurotech.com PCI special interest group PCI Bus specification and list of manufacturers: www.pcisig.org USB information Universal Serial Bus (USB) specification and product information: www.usb.org... -
Page 27: Appendix B - Rohs Compliance
HS Compliance The Restriction of the use of certain Hazardous Substances (RoHS) Directive came into force on 1st July 2006. The ISIS board shall be designed using RoHS compliant components, and manufactured to comply with the RoHS Directive. Eurotech has based its material content knowledge on a combination of information provided by third parties and auditing our suppliers and sub-contractor’s operational activities and arrangements. -
Page 28: Eurotech Group Worldwide Presence
Eurotech Group Worldwide presence Americas Europe Asia North America Central & Southern Europe Japan EUROTECH USA EUROTECH Italy ADVANET US toll free +1 800.541.2003 tel. +39 0433.485.411 tel. +81 86.245.2861 tel. +1 301.490.4007 fax +39 0433.485.499 fax +81 86.245.2860 fax +1 301.490.4582 e-mail: sales-it@eurotech.com... - Page 29 www.eurotech.com...
Need help?
Do you have a question about the ISIS and is the answer not in the manual?
Questions and answers