Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Amate Audio N12WP
Summary of Contents for Amate Audio N12WP
- Page 1 User’s manual May 2018...
- Page 2 13. The equipment shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the device. 14. For hanging and installation, use manufacturer recommended accessories only. Amate Audio...
- Page 3 May 2018 1. INTRODUCTION 1.1. General Amate Audio would like to thank you for your confidence in our NITID Series. We suggest you to carefully read the following instructions in order to obtain the best results in performance. 1.2. Features and presentation...
- Page 4 +/-. Fig. 2. N218WP connectors 2.3. Connection description (N12WP) A) SPEAKON: The N12WP uses two NL4MPR Speakon terminals and is duly prepared for a perfect connection in a parallel system. Terminal Pins +1/-1 must be always used, disregarding the +2/-2 which are not internally connected.
- Page 5 HD3200 Model N12WP Model N12WP Mode Stereo Stereo Impedance 8Ω Impedance 8Ω Impedance 8Ω 4Ω Program power 1000W 1750W One unit of HD3200 (in stereo mode) can feed up to four units of N12WP. Fig. 4. N12WP configuration Amate Audio...
- Page 6 DSP206/608 Impedance 8Ω Model HD4000 Mode Bridge Bridge Impedance 4Ω 8Ω Model N18WP Program power 4000W 2400W Impedance 8Ω One unit of HD4000 (in bridge mode) can feed up to two units of N18WP Fig. 5. N18WP configuration Amate Audio...
- Page 7 Full-range NITID systems in SPEECH or XOVER presets, the N12WP, N18WP and N218WP must operate in positive polarity. When the N12WP, N18WP or N218WP are used in conjunction with the Full-range NITID systems in FLAT, NEARFIELD, LONGTHROW, SMOOTH, MONITOR presets, the N12WP, N18WP and N218WP must operate in negative polarity.
- Page 8 NITID N12WP_N18WP_N218WP May 2018 LPF80 80 Hz low pass filter LPF80+3 80 Hz low pass filter 3) +3dB boost at 50Hz (N12WP,N18WP) 3) +3dB boost at 44Hz (N218WP) LPF90 90 Hz low pass filter LPF90+3 90 Hz low pass filter...
- Page 9 110 Hz low pass filter 3) +3dB boost at 50Hz (N12WP,N18WP) 3) +3dB boost at 44Hz (N218WP) LPF120 (only for N12WP, N18WP) 120 Hz low pass filter LPF120+3 (only for N12WP, N18WP) 120Hz low pass filter with +3dB boost at 50Hz...
-
Page 10: Mounting And Placement
CARD80/90/100/110/120* (*120 only for N18WP) Cardioid polar pattern, with processing, delay and inverse polarity Fig. 7. Recommended PRESETS for N12WP, N18WP and N218WP 3. MOUNTING AND PLACEMENT For a proper installation of the acoustic cabinet systems, it is strongly recommended to carefully read the following advices. - Page 11 They should regularly inspected and replaced if in doubt. When flying enclosures from ceiling support structures, extreme care should be taken to assure the load bearing capabilities of the structures. Do not fly systems from unsafe structures. Amate Audio...
- Page 12 NITID N12WP_N18WP_N218WP May 2018 All flying accessories that are not supplied by Amate Audio are the user's responsibility. Use at your own risk. It is useful to fly low frequency reinforcement units on the top of the system, as they are the heaviest enclosures.
- Page 13 In its minimum and standard configuration a Cardioid setup consists of a stack of three subwoofer cabinets (for N12WP and N18WP) and of a horizontal line of three subwoofer cabinets (for N218WP). Only one subwoofer is needed to compensate for the energy of the other two radiating to the front.
- Page 14 NITID N12WP_N18WP_N218WP May 2018 Fig. 15. Cardioid configuration for N18WP subwoofer Fig. 16. Cardioid configuration for N12WP subwoofer Amate Audio...
- Page 15 The front facing subwoofers must be driven with [LPF110] preset and the back facing subwoofer must be driven with [CARD110] preset. e) The front facing subwoofers must be driven with [LPF120] preset and the back facing subwoofer must be driven with [CARD120] preset. Amate Audio...
- Page 16 [LPF110] [LPF120] [CARD80] [CARD90] [CARD100] [CARD110] [CARD120] [LPF80] [LPF90] [LPF100] [LPF110] [LPF120] Fig. 17. Cardioid presets for N18WP subwoofer [LPF80] [CARD80] [LPF80] [LPF90] [CARD90] [LPF90] [LPF100] [CARD100] [LPF100] [LPF110] [CARD110] [LPF110] Fig. 18. Cardioid presets for N218WP subwoofer Amate Audio...
- Page 17 [LPF100] [LPF110] [LPF120] Fig. 19. Cardioid presets for N12WP subwoofer When placing the subwoofers in a cardioid configuration keep a distance to walls of at least 60 cm in order not to affect the radiation of the central reversed cabinet.
-
Page 18: Technical Features
NITID N12WP_N18WP_N218WP May 2018 5. TECHNICAL FEATURES N12WP N18WP N218WP Impedance Nominal 8 Ω 8 Ω 4 Ω Power R.m.s 400 W 1200 W 2400 W Program 800 W 2400 W 4800 W Connectors 2 x Speakon NL4MPR input 1 x Speakon &... - Page 19 T. +34 93 735 65 65 – F. +34 93 735 60 48 – info@amateaudio.com R&D and FACTORY: Violinista Vellsolà, 18 · 08222 Terrassa T. +34 93 736 23 90 – F. +34 93 786 47 00 Barcelona – SPAIN www.amateaudio.com © Copyright 2018 by Amate Audio S.L.
Need help?
Do you have a question about the N12WP and is the answer not in the manual?
Questions and answers