Sixnet EnterprisePro GSM R-1300-G Quick Start Manual

UNPACKING INSTRUCTIONS
Unpack the Sixnet Wireless unit and verify the following
1
components are enclosed for the EnterprisePro
(Figure A).
Figure A: Package Contents R-1300-G or R-3300-G:
Power Supply Power Supply*
(United States) (International)
Not Shown: Antenna included with model R-1300 or R-3300
* Non-US power supplies require customer-supplied power cord to connect power to
AC power outlet
If any items are missing, please contact Sixnet Wireless at
2
+1 800 489 7781.
Optional item to use for Out-of-Band (OOB) Management
3
function of the Sixnet Wireless modem: Cisco DB9 to RJ45
Console Cable.
GSM MODELS R-1300-G & R-3300-G
In most situations, the R-1300 or R-3300 will arrive with the
1
SIM card installed. If not, open the case...
Insert the SIM supplied by your carrier into the SIM socket.
2
Be sure the SIM is securely fastened by pushing the metal
slide outward to the lock position. Replace the cover and attached
the antenna.
Note: The notch on the SIM card should be on the bottom right hand side of the
SIM socket.
Open
Attach power supply connector to the "barrel" power outlet on
3
the back of the unit and connect power supply plug to an AC
power outlet.
331 Ushers Road • Ballston Lake, NY 12019 • USA • T +1 518 877 5173 • F +1 518 877 8346 • sales@sixnet.com
TM
Router
Ethernet Cable
(6' CAT 5E 568B)
Closed
Verify the POWER (green) LED is lit to indicate that the unit is
4
receiving power.
Please allow 2-4 minutes for the unit to connect to the cellular
5
network. When this has occurred the Signal Strength LEDs
should light up from 1 to 4 LEDs. Sixnet Wireless recommends
2 bars or greater for proper functionality of the unit. If signal
strength is showing 1 LED or showing the top and bottom
LEDs (1 and 4 positions), please refer to the User Manual at
www.sixnet.com.
6 Connect to the Ethernet RJ45 port for network connectivity.
ACCESSSING THE GRAPHICAL USER INTERFACE (GUI)
Connect PC to EnterpriseProTM Router
1
The Ethernet Port on the EnterprisePro
sensing", which means a straight through or cross-over cable
can be used to connect to the Sixnet router.
Connect a CAT-5 Ethernet cable between the local PC and the
unit's Ethernet port. Verify the link LED is lit.
Setup PC IP Address for DCHP
2
For assistance with configuring your PC, see the appropriate
Microsoft Windows support webpage listed at:
http://support.microsoft.com.
PC to Ethernet Interfaces
Select "Use the following IP address" and fill in the blank fields
with the information below:
Ethernet 0
IP address 192.168.0.2
Subnet mask 255.255.255.0
Default gateway 192.168.0.1
Preferred DNS 192.168.0.1
Access Graphical User Interface
3
Open a web browser & enter the following in the
address bar:
Ethernet 0: http://192.168.0.1:10000/
Ethernet 1: http://192.168.1.1:10000/
LOGIN INSTRUCTIONS
• User Name enter:
admin (lowercase letters)
• For Password enter:
six digit serial number of unit (lowercase)
Upon successfully logging in you will see the following screen
(Figure B on reverse side)

QUICK START GUIDE

TM
EnterprisePro Router
GSM R-1300-G or R-3300-G
TM
Router is "auto-
Ethernet 1
192.168.1.2
255.255.255.0
192.168.1.1
192.168.1.1
www.sixnet.com