Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Siqura XCU Fusion
Summary of Contents for Siqura XCU Fusion
- Page 1 XCU Fusion 316L stainless-steel dual imager camera...
- Page 2 Any company, brand or product names mentioned in this manual are registered trademarks of their respective owners. Liability Siqura accepts no liability for claims from third parties arising from improper use other than that stated in this manual. Although considerable care has been taken to ensure a correct and suitably comprehensive description of all relevant product components, this manual may nonetheless contain errors and inaccuracies.
-
Page 3: Table Of Contents
Contents About this manual ..................Copyright and trademarks ..............Typographical conventions ..............Compliance information ................ Identification .................... Models ....................Product markings ................. Preparations ..................... Unpack ....................Check package contents ............... Discard packaging materials ..............Cables and connectors ................Recommended cables ................Connectors .................. -
Page 4: About This Manual
About this manual What's in this manual This manual gives you the information you need to install the XCU Fusion camera. It tells: ● How to mount the camera ● How to connect the camera ● How to power the camera Who this manual is for These instructions are for all professionals who will install the XCU Fusion. -
Page 5: Typographical Conventions
CAUTION! Follow these precautions to prevent potential injury or material damage. DANGER! Follow these safeguards to prevent serious injury or death. Compliance information The XCU Fusion is in conformity with the certifications listed below. Certifications: ● IP67 ● ●... -
Page 6: Identification
The swivel on the bracket is used to fix the pan and tilt position of the camera. ● Ceiling mount: This is the part with which the XCU Fusion can be ceiling or wall/pole mounted. ●... -
Page 7: Product Markings
Identification Product markings The back of the camera housing has a label complying with CE markings. The label shows: ● Camera model name ● Article number (including bar code) ● Power supply (Volt) ● Frequency (Hertz) ● Current consumption (Amps) ●... -
Page 8: Preparations
For better grip and protection, you are advised to wear slip-resistant safety gloves when handling the unit. Check package contents The package contents include the items below. Notify your supplier if any item is missing. Camera ● XCU Fusion unit Documentation ● 1x Quick Start Guide Discard packaging materials ●... -
Page 9: Cables And Connectors
Cables and connectors This chapter gives the requirements for cables and connectors used to connect the camera to power and network. In This Chapter 4.1 Recommended cables....................9 4.2 Connectors......................9 Recommended cables Depending on the power supply, we recommend use of the following cables: ●... -
Page 10: Ethernet
Cables and connectors CON CONEC PLUG Front view IP67 rated only when covered or mated Cable range 6-12 mm Screw termination, Wire range 0.5 – 1.5 mm2 Temperature range -40 °C to +85 °C 4.2.2 Ethernet The standard Ethernet connector, located on the bottom plate of the camera, is the RJ-45 connector. - Page 11 Cables and connectors Optional fibre (2SM) Optional fibre (2MM) Cable part of the connector The contra parts of the above connectors are available from Siqura as accessories.
-
Page 12: Mount And Connect
Mount and connect ● Installation should be done by a qualified engineer and should conform to the local code of practice and all relevant local and international standards. ● Disconnect the power from the camera during installation. ● It is recommended to fix the camera or its mounting brackets with anchors or screws that can hold 100 kg or more per anchor or screw. -
Page 13: Mount The Bracket
Mount and connect XCUSS01 Sunshield SCUFP01 Safety cable (standard supplied with mounts) 5.1.2 Mount the bracket ● When mounting the wall bracket, use anchors and screws (M8) which are appropriate for the mounting surface. ● Each anchor or screw must be able to hold 100 kg. Attach the bracket to the wall Mark the drill hole positions (see the drilling template below). -
Page 14: Attach Safety Cable
Attach the camera to the ceiling mount (see "Mount the camera" on page 17). Lower the camera onto the swivel. Slide the camera into locking position on the swivel. Tighten the four locking nuts which fasten the camera to the bracket. Wall mounted XCU Fusion... -
Page 15: Connect To Network
Mount and connect 5.1.5 Connect to network Connect the network cable Open up the network connector cap. Note: Leave the cap attached to its strap for re-use if you should need to disconnect the network cable at a later stage. Use a tie wrap to secure the cap against wind, if need be. -
Page 16: Check Installation
Ceiling mounting 5.2.1 Ceiling mount accessories The following accessories can be supplied for ceiling mounting: ● XCUCM01: Heavy duty ceiling mount for XCU Fusion ● XCUCM02: Ceiling mount for XCU Fusion ● XCUSS01: Sunshield (only for use with ceiling mount XCUCM02) -
Page 17: Mount The Ceiling Mount
Mount and connect 5.2.2 Mount the ceiling mount ● When mounting the ceiling mount, use anchors and screws (M8) which are appropriate for the mounting surface. ● Each anchor or screw must be able to hold 100 kg. Attach the mount to the ceiling Mark the drill hole positions (see the drilling templates below). - Page 18 Tighten the two locking nuts which fasten the camera to the ceiling mount. Bottom view of properly mounted camera XCU Fusion ceiling mounted on XCUCM01 heavy duty XCU Fusion ceiling mounted on XCUCM02 Attach the camera to the ceiling mount (wall or pole mounting) Remove the screws that fasten the inner bracket to the outside bracket and separate the two brackets.
-
Page 19: Connect To Network And Power
Position the camera and inner bracket inside the outside bracket so they form a ' U' shape together. Tighten the screws which fasten the inner bracket to the outside bracket. XCU Fusion wall/pole mounted on XCUM02 5.2.4 Connect to network and power To connect the camera to the network and power, follow the instructions of Connect to network ( on page 15) and Connect to power ( on page 15). -
Page 20: Maintenance
Maintenance and inspection intervals The XCU Fusion has been designed especially for the harsh environment of traffic tunnel applications and requires little or no maintenance. The camera is fanless and does not include any parts which are prone to wear and tear. Therefore, do not open the camera housing for any maintenance activities. -
Page 21: Dimensions
Dimensions In This Chapter 7.1 Wall/Pole mount....................21 7.2 Ceiling mount....................... 22 Wall/Pole mount XCU Fusion with sunshield mounted on XCUWM01, top view XCU Fusion with sunshield mounted on XCUWM01, side view... -
Page 22: Ceiling Mount
Dimensions XCU Fusion with sunshield mounted on XCUWM01, front view Ceiling mount XCU Fusion mounted on XCUCM01 heavy duty, top view XCU Fusion mounted on XCUCM01 heavy duty, side view... - Page 23 Dimensions XCU Fusion mounted on XCUCM01 heavy duty, front view XCU Fusion with sunshield mounted on XCUCM02, top view XCU Fusion with sunshield mounted on XCUCM02, side view...
- Page 24 Dimensions XCU Fusion with sunshield mounted on XCUCM02, front view XCU Fusion with sunshield mounted on XCUCM02 in U form, top view XCU Fusion with sunshield mounted on XCUCM02 in U form, side view...
- Page 25 Dimensions XCU Fusion with sunshield mounted on XCUCM02 in U form, front view...
Need help?
Do you have a question about the XCU Fusion and is the answer not in the manual?
Questions and answers