invotel SX2010 Manual

Problems
1. • Unplug the phone lines; Wait 60 seconds then Plug them back IN.
Adapter not working or
make sure the phone line is plugged in securely.
stopped working
• Select Line 1 on the phone & make sure that there is dial tone.
Repeat for Line 2
• check audio cord; try inserting it half way, adjust the volume on your
2. No Audio
audio source if needed to hear it.
• Verify that the audio source is playing by itself, listen to it. Use the
3. Audio source is OK but no
Headphone jack on a CD player not the "line out"
audio when device is
• Set Volume to Medium.
activated as per ALT1 or
ALT2 setting. • If answering a call allow a second before placing the call on HOLD.
• Check to see if L1 or L2 lights on this device has turned ON
• SX2010 does not activate by pressing Hold button in ALT1 you need
to press Flash button 1
models wait a second after pressing Flash then press Hold.
• If ALT2, your telephone is not compatible to activate just by hold, use
ALT1 setting via Flash then Hold.
4.
MOH works but audio does • Press FLASH button to stop the audio
not stop when call is picked
• Wire distance to adapter may be too long(more than 200 feet),
up in any setting
Centralize the location of device to be as close as possible to the
phones.
5. • Try changing the setting to ALT1 setting and follow the Operation in
Some Phones work , some
ALT1 settings.
do not in ALT2 setting
6. • Press FLASH button to stop it.
Some times audio starts to
• The call needs to be on Hold at least 4 seconds before it can be
play by it self or does not
voice deactivated, use Flash to deactivate.
by
deactivate voice
• When you hang up, wait 2 seconds before selecting the same line.
• Check for other devices sharing that line like Message indicator,
Answering machine, Alarm system, Modem etc. Use a privacy
module between the line and that device to keep them off the line
when line is being used by your phone.
• Set your Alarm system and/or your DSL line to share FAX line.
• Excessive wiring- Total wire length per line must be under 200 feet.
• Try putting the call back on Hold, wait 3-4 seconds then pick up.
Audio shuts off or flickers • Extensive audio volume. Adjust the volume to proper level.
7.
Innovative Telecommunication Technology LLC
1112 Montana Ave Suite 250 Santa Monica, CA 90403 USA
Tel: 310-899-0078 Fax: 310-857-6401 http://www.invotel.com
Possible Cause / Solution
st
then Hold button. On some telephone
®
Connect "WALL jack" to your "Wall" Jacks using the provided cord
•
This device monitors all the telephones through the lines. You may use a splitter
• • • •
(T adapter) at the Wall jack to connect both this device and a telephone. If you
do not have a splitter use the "PHONE" jack on this device to plug the
telephone.
Please note that just one phone may be optionally connected to this
device, other telephones remain connected to their own wall jacks.
If you have two wall jacks each with one phone number, then you need to use a
• • • •
"2 line coupler" to combine the 2 phone numbers into one jack for this device.
Or contact your phone installer and tell them you want to convert a wall jack from
RJ11 to RJ14
Plug the Audio cable into Audio IN jack on the AudioImage™ Music On Hold
controller, Plug the other end of audio cable into the "Headphone" jack of your
audio source such as digital player (8 ohm or 600 ohm), Radio, CD Player, PC
CD ROM headphone, PC sound card, speakers output etc.
We recommend you to set the volume on your audio source to mid level
Note: extensive volume can shut off the on-hold audio.
(please note some music titles are not royalty-free and you may want to use the royalty-
free music titles to avoid annual licensing payments to ASCAP and BMI for playing those
titles on-hold)
DSL: If you have DSL line, this device needs to be installed after the DSL filter
(otherwise internet may not work properly)
VOIP/Vonage: if you have D-Link VTA-VD phone adapter, you need a "2 line
coupler" to be able to connect it to SX2010
P4

Music-On-Hold Adapter Installation

AudioImage
™
Model # SX2010
Rev 25.5
ALT1 ALT2
Phone
L2 L1
L1 &2
RCA
Audio IN OUT
.
Wall
jack
L1 & 2
IN