Table of Contents
Advertisement
Customer Service Ph: 1800 126 659
e-mail: info.au@delonghigroup.com
Customer Service Ph: 0508 200 300
e-mail: info.nz@delonghigroup.com
De'Longhi Appliances via Seitz, 47 31100 Treviso Italia www.delonghi.com
Proudly distributed by
De'Longhi Australia Pty Limited
P.O. BOX 4540
CASULA MALL NSW 2170
Fax: 1800 706932
www.delonghi.com.au
De'Longhi New Zealand Limited
99 Khyber Pass Road
Grafton 1023
Auckland, New Zealand
P.O. Box 58-056 Botany
MANUKAU 2163
Fax: 0508 200 301
www.delonghi.co.nz
Advertisement
Table of Contents
Related Manuals for DeLonghi HFX85W20
Summary of Contents for DeLonghi HFX85W20
- Page 1 De’Longhi New Zealand Limited 99 Khyber Pass Road Grafton 1023 Auckland, New Zealand P.O. Box 58-056 Botany MANUKAU 2163 Customer Service Ph: 0508 200 300 Fax: 0508 200 301 www.delonghi.co.nz e-mail: info.nz@delonghigroup.com De’Longhi Appliances via Seitz, 47 31100 Treviso Italia www.delonghi.com...
- Page 2 HFX85W20 AIR PURIFIER, HEATER AND COOLING FAN Instructions for use This product is only suitable for well insulated spaces or occasional use...
- Page 5 IMPORTANT WARNINGS Danger of burns!! Safety warnings Failure to observe the warning could result in burns or scalds. - WARNING: In order to avoid Danger! overheating, do not cover the Failure to observe the warning may result in life threatening heater during operation as this injury by electric shock.
-
Page 6: Installation
damage to the heater. INTRODUCTION Thank you for choosing a De’Longhi product. Please take a - The use of extension leads is not rec- few minutes to read these instructions. This will avoid all risks ommended. and damage to the appliance. However if they cannot be avoided, follow the instructions accompanying DESCRIPTION... -
Page 7: Starting Instructions
Starting instructions mode using ventilation levels 1 through 5. Please note: the filter is provided with a protective Heating mode wrapper around it that needs to be removed before first use. To select this operating mode, press the heating button Before turning on the appliance extract the filter from (F) on the remote control, the display shows the its housing as explained in the filter maintenance... -
Page 8: Timer Operation
Examples: cooling fan mode Press the temperature button (G) to select desired temperature (within 4/5 seconds). Press cooling fan button (M) , the display shows the symbol . Press the speed button (L) to increase or decrease the fan speed (within 4/5 seconds). Press the speed button (L) to increase or ECO function... -
Page 9: Airflow Direction
available values are the following: 0.5h; 1h; 2h; 4h; 6h; Oscillation button 8h; 12h. Once having set the desired time, to confirm wait If you want the appliance to distribute the airflow over a about 4-5 seconds. When the programmed time has been larger area, press the oscillation button (J) on remote control. - Page 10 button (H) and timer button (K) together; three brightness levels are available, the display shows: "L1", "L2", "L3" for 4-5 seconds, and within this time is possible increase or decrease the brightness level using the speed buttons (L), respectively. Elapsed the 4-5 seconds, the last level of brightness selected will be shown on the display.
-
Page 11: Maintenance
The appliance comes on with the opposite function set before The unit is automatically programmed to remind you to it was shut off with a predefined temperature set in case of change the filter. heating and a predefined speed in cooling fan. After a predefined number of working hours the unit will display CF message cyclically, indicating that the filter must MAINTENANCE... -
Page 12: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE SOLUTION Temperature sensors are not working Please contact Customer Service The display shows "pf" and emits properly a beep Product doesn’t turn on Check that the plug is connected to the Plug in outlet The set temperature has been reached Use the “+”... - Page 13 The display shows "Ht" or "It" blinking The internal temperature is too high. Check the appliance is correctly The air intake or outlet grille is positioned respecting the minum obstructed distances from the wall, or objects, as indicated on the instruction manual, if not, position the appliance correctly Remove the obstruction Disconnect the plug from the outlet...