Page 1
Model Aircrafters www.arizonamodels.com Albatros C.III Assembly and Historical Information...
Page 2
NOTE: This manual is for all scale size kits. The construction article is written for the original design scaled at 1/6. Adjust the directions accordingly.
Page 13
A registered tradename of Prototype Production and Engineering inc. 14795 North 78th Way Unit 800, Scottsdale Arizona 85260. Reference Photo Plate SHEET 3 of 8 Copywrite 1997 by Arizona Model Aircrafters a registered tradename of Prototype Production and Engineering inc.
Page 14
A registered tradename of Prototype Production and Engineering inc. 14795 North 78th Way Unit 800, Scottsdale Arizona 85260. Reference Photo Plate SHEET 4 of 8 Copywrite 1997 by Arizona Model Aircrafters a registered tradename of Prototype Production and Engineering inc.
Page 15
A registered tradename of Prototype Production and Engineering inc. 14795 North 78th Way Unit 800, Scottsdale Arizona 85260. Reference Photo Plate SHEET 5 of 8 Copywrite 1997 by Arizona Model Aircrafters a registered tradename of Prototype Production and Engineering inc.
Page 16
A registered tradename of Prototype Production and Engineering inc. 14795 North 78th Way Unit 800, Scottsdale Arizona 85260. Reference Photo Plate SHEET 6 of 8 Copywrite 1997 by Arizona Model Aircrafters a registered tradename of Prototype Production and Engineering inc.
Page 17
A registered tradename of Prototype Production and Engineering inc. higher horsepower D.111a Version. 14795 North 78th Way Unit 800, Scottsdale Arizona 85260. Reference Photo Plate SHEET 7 of 8 Copywrite 1997 by Arizona Model Aircrafters a registered tradename of Prototype Production and Engineering inc.
Page 18
A registered tradename of Prototype Production and Engineering inc. 14795 North 78th Way Unit 800, Scottsdale Arizona 85260. Reference Photo Plate SHEET 8 of 8 Copywrite 1997 by Arizona Model Aircrafters a registered tradename of Prototype Production and Engineering inc.
Page 19
Fokker D.VII OE.P. ANLASS Throttle Make from wire (not supplied) OE.P. ANLASS Use music wire for throttle cable Magneto Switch Internal Detail Tips Assemble with steel or brass brads or small size D.VII Rudder Bar hardware. Use spacers between assemblies to (shown at 1/12) allow the throttle handle to freely move OE.P.
Fokker D.VII DRUCK OE.P. ANLASS HAND MOTOR NOTB PUMPE PUMPE TANK Magneto Engine Controls Bend pin for handle ALBATROSS FLUGEWERKS HAND MOTOR TANK PUMPE PUMPE Paint Silver Paint Black NOTB DRUCK Make switch levers from scrap wood sand to shape. Refer to photographs of your prototype aircraft for arrangement.
Page 22
Propeller Logo Albatross D.Va UMAMIN PHYLAX 105225 WILHELM MORELL 6. Rpm. H. Tach Face D.Va Rudder Bar (shown at 1/4)
Page 23
Instrument Assembly Instrument bodies made from brass tube or Lense rolled up tube made from manila paper. Assemble with white glue only DO NOT use CA it will fog the crystal. Indicator and handle made Instrument Face from wire. Paint White Magneto Detail Albatross D.Va For these and other great cockpit graphics by Mark Miller go to:...
Page 24
Albatross D.Va For these and other great cockpit graphics by Mark Miller go to: http://wwi-cookup.com/albatros/dva/profiles_markmiller_cockpit.html...
Compass Details ( Not to scale ) Metal tube. ACTUAL SIZE 1 /4 SCALE Aluminum covered or painted acrylic. Aluminum Tube sections Face mounting plate Printed Face Clear Lense Optional Hardware (place groove to brass tube) 12 sets required or you can use the trimmed Scrap Aluminum tube heads of small nails.
Page 26
Fuel Gauge Assembly Music wire Brass or Aluminum tubes Lense Acrylic ring Face Base Plate Face Base Plate Paint Black no hole with hole Full airplane kits include part as part of the metal sets. Stand alone kits have 1/64 Patent Miesten In den...
Seat Seat Bottom Fokker Configuration Shown Seat Back Leather Set Cockpit Combing Seat Harness Stitch around edge of cockpit opening. Use a split Paint clips to steel or flat black. Wire parts are fuel tube section and wrap the leather around. made from music wire or a paper clip (not Use a sharp needle, Soaking the leather first will supplied) the fastener pin and chain are...
Page 28
Typical set up for a working cockpit Shown in the illustration is the layout for an Albatross D.III Specific cockpit details for your model will vary but the basic principal works for most all early aircraft. Instrument Body Assembly Make instrument bodies from rolled strips of aluminum lithoplate or strips of manila folder paper.
Page 36
Model Aircrafters www.arizonamodels.com Copyright 2006 by Arizona Model Aircrafters a registered tradename of Digital Design LLC 13814 N. 56th Place Scottsdale, AZ 85254...
Need help?
Do you have a question about the Albatros C.III and is the answer not in the manual?
Questions and answers