7845GSM / 7845i-GSM QUICK GUIDE
for “C” Series Replacement and New Installations
(WHEN USING ECP MODE ONLY)
This guide explains how to install a 7845GSM or 7845iGSM for basic ECP mode applications primarily
intended to replace "C" series modules. This guide can also be used by experienced installers for new
7845GSM/7845i-GSM installations. Abbreviated programming and registration procedures also provided.
NOTES: A. AlarmNet-I Account: The 7845GSM and 7845i-GSM modules require an AlarmNet–I account.
For new installations, please obtain the account information from the central station prior to programming
this module. For replacement installations, the AlarmNet-I account is created automatically when the module
is registered (based on the existing "C" series account).
B. For Replacement Installations
·
Check the existing device for its current mode and programming options prior to replacing.
·
Do not use the existing “C” radio’s antenna. (AMPS antenna is not compatible with this module).
Programming and Registration
·
By AlarmNet Direct Website: GO TO: https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx
Log in and follow the on-screen prompts. See "Honeywell's Alarmnet Direct" section on back.
·
By 7720P: See procedure below.
·
By Phone (registration only): See below.
PROGRAMMING AND REGISTERING THE MODULE WITH THE 7720P
Registering
Programming
Programming assumes module's default values
A.
If replacing a "C" series module:
Register Replacement Module by pressing
will be used. See Installation Guide for values.
[
] Down Arrow key, Then enter
A.
Connect 7720P to Module.
PIN Number (last four digits of old module's
MIN number) and press Enter.
B.
Enter Program Mode by pressing [ # ], then
"Shift -Y" at the "START PROGRAM MODE"
OR
prompt.
For new 7845GSM/7845i-GSM:
Register Module by pressing
Go to "DEVICE MODE" prompt and confirm
C.
Shift - [
] Up Arrow key.
module is in "ECP" Device Mode. (Refer to the
Installation and Setup Guide if using any other
B.
Wait for the "Registration Success" message
mode.)
to appear. The unit is registered and available
for alarm reporting. Refer to the Installation
D.
Scroll (Using Up/Down Arrows) to "PRIMARY
and Setup Guide if any error messages
CITY ID" prompt and enter ID. (provided by CS)
are displayed.
E.
Go to "PRIMARY CS ID" prompt and enter ID.
For a replacement module, an alarm message
(provided by CS)
(00D0 010B 0) will be sent to the central station
Go to "PRIMARY SUB ID" prompt and enter ID.
indicating the "C" series module has been
F.
(provided by CS)
replaced.
G.
C.
Exit Program Mode by pressing "Shift -ESC," then
Disconnect the 7720P and install module
press "N" at the Review prompt, then press
cover (use cover securing screw for UL
"Shift -Y" at the "EXIT PROG MODE?" prompt.
installations).
PROGRAMMER KEYBOARD COMMANDS
("D" and "F" apply to 7845i-GSM only)
Registering by Phone:
You can also register the module by calling the
COMMAND
FUNCTION
AlarmNet Technical Assistance Center (TAC)
Shift - [A]
Software Revision (month, day, year)
at 1-800-222-6525.
Shift - [B]
MAC Address, SCID, and IMEI Displays
You will need the following information:
Shift - [C]
Time (GMT from AlarmNet network)
· MAC number (found on the label).
Shift - [D]
Network Diagnostics Display (internet status)
· Subscriber information (provided by the
Shift - [E]
GSM Status Display Screens (radio status)
central station), including a city code,
CSID, and a subscriber ID.
Shift - [F]
Network Diagnostic Test
When instructed to do so, triple-click the
Shift - [S]
System Status (faults, battery, line voltage)
tamper switch to complete the registration.
Shift - [T]
Test Alarm (for registered modules only)
Shift - [X]
Reset the module
Shift - [ ]
(UP arrow) Registration for new installation
[ ]
(DN arrow) Registration with PIN for Replacement
[ENTER]
Enter Program Mode