Related Manuals for KICKING HORSE MA200TS
Summary of Contents for KICKING HORSE MA200TS
- Page 1 OPERATION MANUAL MA200TS multi-process welder Serial Number: _________________________________ Where Purchase: _________________________________ Date of purchased: _________________________________...
-
Page 3: Table Of Contents
Installation precaution ..................... 11 6.2. Safety ......................... 12 7. Maintenance ........................... 12 8. Troubleshooting & Service ..................... 13 9. Torch Part Breakdown ......................15 MA200TS Multi-process welder P a g e... -
Page 4: Safety
Do not weld enclosed tanks or containers Prohibit to use welder to unfrozen. Have a fire extinguisher readily available. Hot parts can lead to burn MA200TS Multi-process welder P a g e... - Page 5 The people with heart-pacemaker should be away from the welding arc. Rotating parts may be dangerous Far away from rotating parts. (like fan) Keep the parts of machine in the safe position. MA200TS Multi-process welder P a g e...
-
Page 6: Electrical Principle Drawing
2. Electrical principle drawing MA200TS Multi-process welder P a g e... -
Page 7: Specifications
Duty cycle（40 ） 60% 130A 100% 100A Welding Current Range (A) 40-200 10-180 Welding Voltage Range (V) 16-23 20.4-27.2 0.6、0.8、0.9 Wire Diameter(mm) (steel /stainless steel/flux-cored) Protection class IP23 Insulation class Dimensions（mm） 400*210*340 Weight（Kg） MA200TS Multi-process welder P a g e... -
Page 8: Front And Rear Penal Diagram
4. Front and rear penal diagram Negative output. Positive output. Euro MIG torch connection: connect to NT1 MIG torch. MA200TS Multi-process welder P a g e... -
Page 9: Installation & Operation
Connect to negative output (-) is DCEN. (see installation diagram). 5. Installation & Operation The equipment protection level is IP23. Do not use in the rain! The equipment must be turn off during installation! MA200TS Multi-process welder P a g e... - Page 10 DCEP for steel, stainless steel and aluminum wire. MIG Gun Polarity Lead must connect to positive DCEN for flux cored wire. output (+) MIG Gun Polarity Lead must connect to negtive output (-) MA200TS Multi-process welder P a g e...
- Page 11 Stick welding installation diagram DCEP DCEN TIG welding (scratch start) installation diagram MA200TS Multi-process welder P a g e...
-
Page 12: Electric Service Guide
Attach earth clamp as close as possible to the cutting portion. Do not attach earth cable to the portion that will fall away. MA200TS Multi-process welder 10 | P a g e... -
Page 13: Recommended Welding Parameters
(2) The air humidity of not more than 90%. (3) Avoid environment containing dust or corrosive gas. (4) Avoid sunlight or rain; do not let water into the welding machine. (5) Avoid the strong wind environment. MA200TS Multi-process welder 11 | P a g e... -
Page 14: Safety
Check the electric connection of input/output bar Check and change broken parts in the torch to to avoid bad contact caused by loose or rusted MA200TS Multi-process welder 12 | P a g e... -
Page 15: Troubleshooting & Service
Change it output Press Gas pipe leaks gas Change it gas when test gun switch, Electromagnetic valve output Change it damaged shielded gas Output gas Control switch damaged Repair the switch MA200TS Multi-process welder 13 | P a g e... - Page 16 Welding current is run away control circuit and can be not controlled Check the circuit damaged The crater current can be not The PCB damaged Check it adjusted No post-gas The PCB damaged Check it MA200TS Multi-process welder 14 | P a g e...
-
Page 17: Torch Part Breakdown
Order No. Nozzle Self Insulated 21-37 Nozzle Self Insulated 21-50* Nozzle Self Insulated 21-62 Nozzle Self Insulated 21-37F Nozzle Self Insulated 21-50F Nozzle Self Insulated 21-62F Nozzle Self Shielding LA8201 Contact Tips MA200TS multi-process welder 15 | P a g e... - Page 18 Gun &Cable Assembly 3M TEL1030 Rear spring cable support ES2201 Gun plug housing EH2201 Screw(M4X6) EH2211 Rear lock nut EP2001 Euro connector(Tweco) ETU001 O ring 4x1 Q504010 O ring 4x8 Q504018 Nut M11X1 TEU1011 MA200TS Multi-process welder 16 | P a g e...
- Page 19 NOTES MA200TS MIG/Stick multi-process welder MA200TS Multi-process welder 17 | P a g e...
- Page 20 NOTES MA200TS MIG/Stick multi-process welder MA200TS multi-process welder 18 | P a g e...
- Page 22 WELDKING ONLINE STORE 271, Amber Street, Unit#10, Markham, ON L3R 3J7 Tel: 1 866 686 5088 Fax: 1 866 686 5090 Website: www.weldkingstore.com Printed April 3, 2018...
Need help?
Do you have a question about the MA200TS and is the answer not in the manual?
Questions and answers