Eco Sensor ES701 User Manual

ES701 Passive Infrared (PIR) IP65 Motion Sensor User
Manual

General

The ES701 PIR IP 65 motion sensor is ideal for outdoor or high humidity applications,
such as outdoor lights and bathrooms loads. The sensor has an extruding screw
that can easily be installed directly onto a light fixture.
If, after reviewing this guide, you require additional information or assistance
please contact Eco Heat Equipment at info@ecosensor.co.za, +27 (0)861 999 887,
or www.ecosensor.co.za.

Technical Specifications

§ Voltage: 220 – 240V/AC
§ Frequency: 50/60Hz
§ Load: Incandescent max: 450W
Fluorescent max: 275W
LED max: 150W
§ Detection Angle: 360 °
§ Detection Range: 1.4 m- 8m radius (dependent on mounting height)
§ Light level: 10 – 50 LUX and 24H
§ Time setting: 10 seconds – 60 minutes
§ Dimming Level: 0%, 10%, 20% and 30%, Dimming Function Off
§ Installation height: 2.5 - 7m max
§ Working temperature: -10°C to 35°C
§ IP Rating: IP65
§ Dimensions: Length: 129.6mm (149mm with connector)
Width: 36.4mm
Height: 28mm
Connector inside diameter: 17.1mm
Connector outside diameter: 20.4mm

Safety

Any incorrect use or installation procedure not recommended by the
manufacturer may cause fire, electrical shock or injury to persons.

Box Contents

Your box should contain the following items:
§ Sensor
§ Silicone Washer
§ M20 Nut
§ 2 x spacers
WARNING:
Controlling a load in excess of the specified ratings will damage the unit and lights
and could pose risk of fire and electric shock.
Do not install this unit to control a power socket.

Installation Instructions

WARNING: ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND
LOCAL ELECTRICAL CODES AND STANDARDS.
Note: motion sensors respond to rapid changes in temperature so care should be
taken not to mount the device near a climate control source (i.e. heaters or air
conditioners). Hot or cold draughts will seem like body motion to the sensor and will
trigger the device. Recommended distance from climate control devices is 2m.
1. Turn power off at circuit breaker or fuse
2. Connect wires as per diagram
3. Sensor can be secured onto light fitting
4. Restore power at circuit breaker or fuse
Sensor calibration:
Note: Allow up to 1 minute for the motion sensor to recalibrate after it has been
connected for the very first time. This is only necessary during installation or when
the mains supply is disconnected.
Installation wire diagram – NO DIMMING DIRIVER
–
© Eco Heat Equipment Oct 2016
Installation wire diagram – DIMMING DIRIVER

Operation and Field of View

The motion sensor detects motion within its coverage area and controls the
associated lighting connected to the sensor. The passive infra red (PIR) sensor is
sensitive to the heat emitted by the human body. In order to trigger the sensor the
source of heat must move from one zone of detection to another. The device is
most effective in sensing motion across its field of view and less effective sensing
motion towards or away from its field of view**.
Sensor detection range from side: large motion* across detection zone
*Detection range for large motion at 2.8m height: 14m (diameter).
**Detection Range will decrease with approximately 35% with movement towards
or away from the sensor
Sensor detection range: large motion* towards/away sensor

Motion Sensor Settings and Adjustments

The motion sensor is a Passive Infra Red (PIR) type electronic occupancy detector,
which in turn switches the lights when connected to the motion sensor. There are
five adjustments (three if the dimming function is not used) that can be made to
influence the operation of the motion sensor:
1. RANGE/SENSITIVITY: motion detection range
2. STAND-BY TIME: time delay after motion until shut off/dimming
3. LUX/LIGHT: level of ambient light sensitivity
4. DIMMING LEVEL: level of dimming required*
5. DIMMING TIME: time delay after motion until shut off *
* Only applicable if grey and violet wires are connected to dimming driver
The five adjustments settings are as follows:
Detection/Sensitivity range:
Stand-by time setting range:
Lux (light) sensitivity:
Dimming level: *
Dimming time: *
* Only applicable if grey and violet wires are connected to dimming driver

Motion Sensor Adjustments

The motion sensor's settings is adjusted using the ES-REMD remote control.
1 of 2
20%, 50%, 75%, 100%
10 sec, 1 min, 5min, 15min, 30min, 60 min
24H,10 LUX, 30LUX
0%, 10%, 20%, 30%
24H, 1 min, 30min, 60min, 24H