Lippert Components FASTEC Owner's Manual
  1. Manuals
  2. Brands
  3. Lippert Components Manuals
  4. Intercom System
  5. FASTEC
  6. Owner's manual
Lippert Components FASTEC Owner's Manual

Lippert Components FASTEC Owner's Manual

Rv entry door latch
Hide thumbs

Advertisement

Table of Contents

RV Entry Door Latch
OWNER'S MANUAL
Page 1
Rev: 06.13.18
CCD-0001435

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FASTEC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Lippert Components FASTEC

Summary of Contents for Lippert Components FASTEC

  • Page 1 RV Entry Door Latch OWNER'S MANUAL Page 1 Rev: 06.13.18 CCD-0001435...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS FASTEC ENTRY DOOR LATCH SOUTHCO KEYLESS ENTRY DOOR LATCH RVLOCK KEYLESS ENTRY DOOR LATCH Installation Removal of Existing Handle Installing the RVLock Programming the RVLock Programming a new code into your RVLock Keypad Syncing the RVLock handle with your Keypad or Remotes...

  • Page 3: Fastec Entry Door Latch

    FASTEC ENTRY DOOR LATCH Fastec door latches are installed on about 98% of all entry doors in the RV industry. They are the only manual latch used by Lippert Components, Inc. LCI Fastec door latch comes in 3 colors; Black-50% usage; White - 40% usage; Chrome - 10%.

  • Page 4: Southco Keyless Entry Door Latch

    Southco, Inc. door latches are used in Lippert’s Keyless Entry Door systems. All Southco units are black and the door handle is slightly curved, as opposed to the straight door handle on the Fastec. Keypad (Fig. 1) Keyfob (Fig. 2) Fig.
  • Page 5 Fig. 7 Fig. 5 Fig. 6 The receiver is mounted just below the entry door window. The keypad and the keyfob are all matched directly to the receiver. A small black sticker with the code number is affixed directly to each component. On the keypad, the sticker is located under the 9 - 0 button (Fig.

  • Page 6: Rvlock Keyless Entry Door Latch

    RVLOCK KEYLESS ENTRY DOOR LATCH Installation Removal of Existing Handle Securely latch the door in the open position to make it easy to work on. This will keep it from moving while you are working. Remove the four screws from the back of the existing handle; the back of the handle will fall away from the door.

  • Page 7: Programming The Rvlock

    Programming the RVLock Press the lock and unlock buttons on the RVLock remote(s) or, if you have a keypad, type in the numeric code (default code is 1234) and press the lock button on the keypad to make sure the lock functions.

  • Page 8: Syncing The Rvlock Handle With Your Keypad Or Remotes

    Syncing the RVLock handle with your Keypad or Remotes Lightly press the learning button with a paper clip through the pin hole located under the interior handle. A beep will confirm that you have entered the programming mode. Now repeat pressing the lock button on your remote until the handle confirms with a series of rapid beeps (usually takes one or two times).

  • Page 9: Troubleshooting

    Troubleshooting A. When someone has tried to open the door after the handle is locked, the dead bolt may be on a bind making it difficult for the handle to retract the dead bolt. Push the door closed tightly and retry the remote or use your key.
  • Page 10 The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).  LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized LCI representative has been provided.  Any unauthorized use shall void any applicable warranty. ...

This manual is also suitable for:

Rvlock keylessSouthco keyless

Table of Contents