Guild BTC110G Instruction Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

GUILD

Tile cutter

Instruction Manual

Important

- Please read these instructions fully before operating or maintaining your Guild Tile cutter

These instructions contain important information that will help you get the best from your Guild

Tile cutter, ensuring it remains safe to operate.

If you need help or have damaged or missing parts, call the Customer Helpline on 0333 3201989

After Sales Support

UK/Ireland 0333 3201989

Help@guildpowertools.co.uk

BTC110G

Table of Contents

Summary of Contents for Guild BTC110G

Page 1 Important - Please read these instructions fully before operating or maintaining your Guild Tile cutter These instructions contain important information that will help you get the best from your Guild Tile cutter, ensuring it remains safe to operate. If you need help or have damaged or missing parts, call the Customer Helpline on 0333 3201989...
Page 2: Table Of Contents
Contents Safety Information ��3 In The Box ��7 Accessories ��7 Operating Instructions ��8 Repair �� 13 Storage �� 16 Transportation �� 16 Trouble Shooting �� 17 Technical Data �� 18 Environmental Protection �� 18 Guarantee �� 19 Declaration of Conformity �� 20 Plug Replacement (Uk &...
Page 3: Safety Information
Safety Information Important - Please read these instructions fully before starting assembly Warning Symbols To reduce the risk of injury, Please read the instruction manual Wear eye protection Wear ear protection Wear dust mask Wear protective gloves Use correct size of blades Do not use segmented blade Wet cut only Caution,risk of cutting...
Page 4 Safety Information Important - Please read these instructions fully before starting assembly Safety Instructions WARNING! When using electric tools basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury including the following� Read all these instructions before attempting to operate this product and save these instructions”�...
Page 5 Safety Information Important - Please read these instructions fully before starting assembly Safety Instructions and sharp edges. 12. Secure work - Where possible use damps or a vice to hold the work. It is safer than using your hand. 13. Do not overreach - Keep proper footing and balance at all times.
Page 6 Safety Information Important - Please read these instructions fully before starting assembly Safety Instructions – for tools provided with an isolating transformer: Never use the tool without the transformer delivered with the tool or of the type as specified in these instructions, –...
Page 7: In The Box
In The Box Parts Extension table Parallel cutting guide Fixing knob of Parallel cutting guide Angle cutting guide Fixing knob of Angle cutting guide Wheel guard Small spanner for locking nut Water reservoir lid On/Off switch Big spanner for outer flange Carry handle Accessories Diamond blade...
Page 8: Operating Instructions
Operating Instructions NOTE: Before using the tool, read the instruction book carefully. Intended Use This product is intended for Cutting tile or marble, and other similar materials This product is intended for private domestic use only, not for any commercial trade use. It must not be used for any purposes other than those described.
Page 9 Operating Instructions Before you start 1. REMOVE THE WATER RESERVOIR LID (SEE FIG A1,A2,A3) 1) Lift the water reservoir lid (4) up firstly and lift the right side of the water reservoir lid (4), then move to left for removing it. 2�...
Page 10 Operating Instructions Before you start the rotation direction on the wheel guard the rotation direction on the diamond wheel Customer Helpline 0333 3201989...
Page 11 on the wheel guard Operating Instructions the rotation direction on the diamond wheel Before you start INSTALL THE ACCESSORIES (SEE FIG C1-C4) Loosen the supplied screw (f) on the surface. Put the fixing bracket (g) of wheel guard on the surface and using one ruler (not supplied) to keep the diamond blade and the fixing bracket (g) of wheel guard in the same level.
Page 12 Operating Instructions Before you start INSTALL THE PARALLEL CUTTING GUIDE AND ANGLE CUTTING GUIDE (SEE FIG D1-D6) Tighten the two fixing knobs of Parallel cutting guide (8) to both sides of the Parallel cutting guide (1) (Note: please tighten the fixing knobs with the gasket (n) of the Parallel cutting guide, ensure that the fixing knobs not over the gasket ).
Page 13 Operating Instructions Before you start ON/OFF SWITCH (SEE FIG E) ● The saw can be switched on by pressing the green pushbutton “I”. ● The red pushbutton “0” has to be pressed to switch off the saw. Operation NOTE: Put the tile cutter on a clean, stable and flat surface. WARNING: Before switching the tile cutter on, make sure that you have read and understood all of the safety instructions.
Page 14 Operating Instructions Operation FILLING THE WATER RESERVOIR (SEE FIG H) ● Before cutting, the water reservoir must be filled with water. Fill two-thirds of the tray of cold and clear water. The water can cool and lubricate the disk during the cut and it also helps to remove dust. WARNING! Do not add chemicals or detergents to the water.
Page 15 Operating Instructions Operation STRAIGHT CUTS(SEE FIG J) Loosen fixing knobs of the parallel cutting guide (8) at both ends of the parallel cutting guide (1). Set the parallel cutting guide (1) to the desired size. Relock fixing knobs of the parallel cutting guide (8). Place the piece of tile against the parallel cutting guide (8) then push the work piece towards the diamond blade.
Page 16: Repair
Repair This product does not contain any parts that can be repaired by the consumer. Contact a qualified specialist to have it checked and repaired. Storage 1. Clean the product as described above. 2. Store the product and its accessories in a dry, frost-free place. 3.
Page 17: Trouble Shooting
Trouble Shooting Suspected malfunctions are often due to causes that the user can fix themselves. Therefore check the product using this section. In most cases the problem can be solved quickly. WARNING! Only perform the steps described within these instructions! All further inspection, maintenance and repair work must be performed by an authorized service centre or a similarly qualified specialist if you cannot solve the problem yourself! Problem...
Page 18: Technical Data
Technical Data Technical Data Table Voltage 230-240V~50Hz Power input 450W S2:30min No load speed 5400 /min Blade size Ø110 x Ø22.2mm Cutting depth 23mm 16mm Table bevel range 0°, 22.5°and 45° Table size 330~395(L) * 305(W) mm Machine weight 3.70kg Protection class Noise Information A weighted sound pressure...
Page 19: Guarantee
Guarantee This product is selected for DOMESTIC USE ONLY and not for business use. This product is guaranteed against manufacturing defects for a period of 24 months. This does not cover the product where the fault is due to misuse, abuse, use in contravention of the instructions, or where the product has been the subject of unauthorised modifications or alterations, or has been the subject of commercial use.
Page 20: Declaration Of Conformity
Declaration of Conformity This Guild 450W Tile cutter model number BTC110G fully complies with the Machinery Directive 2006/42/EC, Electromagnetic Compatibility Directive 2004/108/EC(before 2016/04/20) and 2014/30/EC(since 2016/04/20), RoHS Directive 2011/65/EU and the following harmonized EU standards EN 61029-1/A11: 2010 EN ISO 12100:2010 ZEK 01.4-08...
Page 21: Plug Replacement (Uk & Ireland Only)
Plug Replacement (Uk & Ireland Only) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: Blue = Neutral Brown = Live Green/Yellow=Earth As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows.