Whalen LANTOFLBB Assembly Instructions Manual

Landon twin over full loft bunk bed with bookshelf stock

Advertisement

Landon Twin over Full Loft Bunk Bed with Bookshelf
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
Stock # LANTOFLBB
ADULT ASSEMBLY REQUIRED
www.whalenstyle.com
Or e-mail your request to parts@whalenfurniture.com
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2017-10-10 Rev. 0001-A Factory: JIYIFO
866-942-5362
LOT NUMBER:
DATE PURCHASED: /
/

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LANTOFLBB and is the answer not in the manual?

Questions and answers

Summary of Contents for Whalen LANTOFLBB

  • Page 1 LOT NUMBER: DATE PURCHASED: / Landon Twin over Full Loft Bunk Bed with Bookshelf Stock # LANTOFLBB ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions...
  • Page 2 ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF THE BUNK BED WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL THAT RUNS THE FULL LENGTH OF THE BED SHOULD BE PLACED AGAINST THE WALL TO PREVENT ENTRAPMENT BETWEEN THE BED AND WALL. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed;...
  • Page 3 TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM ENTRAPMENT OR FALLS • Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed. • Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls.
  • Page 4 Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Lower Footboard Front Post B- Lower Footboard Back Post C- Lower Headboard Front Post (Qty. 1) (Qty.
  • Page 5 Parts and Hardware List S- Upper Mattress Support Slats T- Left Ladder Support U- Right Ladder Support (Qty. 1) (Qty. 1) (Qty. 1) V- Ladder Step W- Upper Bed Stretcher XA- Full Bed Headboard Right Post (Qty. 5) (Qty. 2) (Qty.
  • Page 6 Parts and Hardware List YF- Bookshelf Middle Upper Shelf YG- Bookshelf Top Shelf YH- Bookshelf Back Panel (Qty. 1) (Qty. 1) (Qty. 2) (1) 1/4” x 110 mm Bolt (2) 1/4” x 45 mm Bolt (Qty. 24+1 extra) (Qty. 8+1 extra) (3) 1/4”...
  • Page 7 BOOKSHELF ASSEMBLY 1/4” x 32 mm Bolt 6 x 25 mm Wood Dowel (10 used in this step) (10 used in this step) ④ ⑧ DO NOT fully tighten the bolts initially until all the bolts are ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the bolts.
  • Page 8 BOOKSHELF ASSEMBLY YC YD YE 4. Slide two Back Panels (YH) into the grooves between the lower three shelves (YC, YD and YE) until fully inserted into the Bookshelf Right Side Panel (YB).
  • Page 9 BOOKSHELF ASSEMBLY 1/4” x 32 mm Bolt 6 x 25 mm Wood Dowel (10 used in this step) (10 used in this step) ⑧ ④ 5. Repeat the same procedure to attach the Bookshelf Left Side Panel (YA) at the opposite end. Make sure that the Back Panels (YH) fit securely into the groove of Side Panel (YA).
  • Page 10 UPPER BUNK ASSEMBLY 6.5 mm x 48 mm Tapping Bolt 10 x 50 mm Wood Dowel (4 used in this step) (6 used in this step) ⑦ ⑥ 7. Align and attach one Upper Bed Stretcher (W) to one Upper Cap Rail (L) using two 50 mm Wood Dowels (7) and three 48 mm Tapping Bolts (6).
  • Page 11 UPPER BUNK ASSEMBLY 8 x 30 mm Wood Dowel (4 used in this step) ⑮ 6.5 mm x 100 mm Tapping Bolt 10 x 50 mm Wood Dowel (6 used in this step) ⑤ (6 used in this step) ⑦ 9.
  • Page 12 UPPER BUNK ASSEMBLY 8 x 30 mm Wood Dowel (4 used in this step) ⑮ 6.5 mm x 100 mm Tapping Bolt 10 x 50 mm Wood Dowel (6 used in this step) ⑤ (6 used in this step) ⑦ 11.
  • Page 13 UPPER BUNK ASSEMBLY 10 x 50 mm Wood Dowel (4 used in this step) ⑦ 1/4” x 110 mm Bolt Barrel Nut ① (12 used in this step) (12 used in this step) ⑫ 12. Insert the 50 mm Wood Dowels (7) into the drilled large holes of the Long Guardrail (P) at both ends. Attach two Long Guardrails (P) and the Upper Mattress Side Rail (N) between Upper Posts (F and H) using eight 110 mm Bolts (1) and eight Barrel Nuts (12) as shown above.
  • Page 14 UPPER BUNK ASSEMBLY 4 mm x 35 mm Screw (14 used in this step) ⑩ 14. Lay out the Upper Mattress Support Slats (S) between the wood stoppers on the Ladder Side Rail (M) and the Upper Mattress Side Rail (N). Insert and screw 35 mm Screws (10) into the countersunk holes on each slat.
  • Page 15 UPPER BUNK ASSEMBLY 10 x 50 mm Wood Dowel (4 used in this step) ⑦ BARREL NUT (4 used in this step) ⑫ 1/4” x 110 mm Bolt 1/4” x 38 mm Bolt ① (4 used in this step) (2 used in this step) ③...
  • Page 16 UPPER BUNK ASSEMBLY 4 mm x 30 mm Screw (6 used in this step) ⑨ 17. With the pilot holes as a guide, align and attach one Guardrail Support (R) to the center of the Long Guardrails (P) and the Upper Mattress Side Rail (N) with three 30 mm Screws (9). 18.
  • Page 17 LOWER BUNK ASSEMBLY 6.5 mm x 100 mm Tapping Bolt 10 x 50 mm Wood Dowel (4 used in this step) (4 used in this step) ⑤ ⑦ 19. Insert four 50 mm Wood Dowels (7) into the end holes of two Lower Side Rails (I) and attach them between the Lower Posts (C and D) with four 100 mm Tapping Bolts (5).
  • Page 18 LOWER BUNK ASSEMBLY 6.5 mm x 48 mm Tapping Bolt (6 used in this step) ⑥ 20. Align and attach the Lower Footboard Front Post (A) to the Bookshelf Left Side Panel (YA) by inserting three 48 mm Tapping Bolts (6) through the pre-drilled holes on the Side Panel (YA) and screw into the post.
  • Page 19 LOWER BUNK ASSEMBLY 6.5 mm x 100 mm Tapping Bolt 10 x 50 mm Wood Dowel (4 used in this step) ⑤ (8 used in this step) ⑦ 22. Insert eight 50 mm Wood Dowels (7) into the end large holes of two Lower Back Rails (J). Attach the Back Rails (J) between the Lower Back Posts (B and D) by using four 100 mm Tapping Bolts (5).
  • Page 20 ASSEMBLY OF THE BUNK BED 1/4” x 45 mm Bolt (8 used in this step) ② Bed Connector Pin 4 mm x 30 mm Screw Metal Bracket (4 used in this step) (2 used in this step) (1 used in this step) ⑭...
  • Page 21 ASSEMBLY OF THE BUNK BED 6.5 mm x 48 mm Bolt (2 used in this step) ⑥ 26. Fasten the Bookshelf Side Panels (YA and YB) to the Upper Footboard Posts (E and F) by inserting two 48 mm Tapping Bolts (6) through the pre-drilled holes and securely screw into the posts.
  • Page 22 ASSEMBLY OF THE LADDER 6.5 mm x 48 mm Bolt 10 x 50 mm Wood Dowel (10 used in this step) (10 used in this step) ⑥ ⑦ 27. Insert the 50 mm Wood Dowels (7) into the large holes of Ladder Steps (V) at both ends. Attach Left and Right Ladder Supports (T and U) to the Ladder Steps (V) using the 48 mm Tapping Bolts (6).
  • Page 23 ASSEMBLY OF THE LADDER 4 mm x 19 mm Screw (2 used in this step) ⑬ 28. Hook the ladder securely over the top of the Ladder Side Rail (M), between the Upper Footboard Front Post (E) and the Front Guardrail Post (Q) in the opening provided. Secure the Ladder Hooks in place by using two 19 mm Screws (13).
  • Page 24 FULL BED ASSEMBLY 6.5 mm x 48 mm Tapping Bolt 10 x 50 mm Wood Dowel (8 used in this step) (4 used in this step) ⑥ ⑦ NOTE: Please follow the instructions carefully to ensure a safe and sturdy bed. Do not fully tighten the bolts until all rails and guardrails are attached.
  • Page 25 FULL BED ASSEMBLY 8 x 30 mm Wood Dowel (4 used in this step) ⑮ 6.5 mm x 100 mm Tapping Bolt 10 x 50 mm Wood Dowel (6 used in this step) ⑤ (6 used in this step) ⑦ 31.
  • Page 26 FULL BED ASSEMBLY 8 x 30 mm Wood Dowel (4 used in this step) ⑮ 6.5 mm x 100 mm Tapping Bolt 10 x 50 mm Wood Dowel (6 used in this step) ⑤ (6 used in this step) ⑦ 33.
  • Page 27 FULL BED ASSEMBLY XA XB XC XD 1/4” x 110 mm Bolt ① Barrel Nut (8 used in this step) (8 used in this step) ⑫ 35. Insert two Barrel Nuts (12) into each end of the Full Bed Mattress Side Rails (XH). Be sure that the cross slot on the Barrel Nut faces out and the threaded hole points towards the entry of the bolt along the rail.
  • Page 28 FULL BED ASSEMBLY 1/4” x 32 mm Bolt 4 mm x 35 mm Screw (3 used in this step) (14 used in this step) ④ ⑩ 37. Lay out the Full Bed Mattress Support Slats (XI) onto the strips on the Mattress Side Rails (XH). Make sure that the end slats are located close to the Lower Posts.
  • Page 29 ASSEMBLY INSTRUCTIONS 39. Position the assembled Full Bed against the Lower Back Rails (J) for space saving.
  • Page 30: Care And Maintenance

    Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture.

Table of Contents

Save PDF