Table of Contents
Advertisement
Quick Links
OPERATING AND MAINTENANCE INSTRUCTIONS MANUAL
HCT908 Hole Cutting Tool
WARNING
If you need additional copies of any literature, or if you have questions concerning the safe
and proper operation of this tool, contact Victaulic, P.O. Box 31, Easton, PA 18044-0031,
Phone: 1-800-PICK-VIC, E-Mail: pickvic@victaulic.com.
REV_C
WARNING
Failure to follow instructions and warnings could result in death,
serious personal injury, property damage, and/or product damage.
• Before operating or servicing any grooving tools, read all
instructions in this manual and all warning labels on the tool.
• Wear safety glasses, hardhat, foot protection, and hearing
protection while working around this tool.
• Save this operating and maintenance manual in a place
accessible to all operators of the tool.
Original Instructions
TM-HCT908
Advertisement
Table of Contents
Related Manuals for Victaulic TM-HCT908
Summary of Contents for Victaulic TM-HCT908
- Page 1 If you need additional copies of any literature, or if you have questions concerning the safe and proper operation of this tool, contact Victaulic, P.O. Box 31, Easton, PA 18044-0031, Phone: 1-800-PICK-VIC, E-Mail: pickvic@victaulic.com.
-
Page 3: Table Of Contents
TM-HCT908 / Operating and Maintenance Instructions Manual TABLE OF CONTENTS Hazard Identification ....4 Operator Safety Instructions ... . 4 Introduction . -
Page 4: Hazard Identification
TM-HCT908 / Operating and Maintenance Instructions Manual HAZARD IDENTIFICATION OPERATOR SAFETY INSTRUCTIONS Definitions for identifying the various hazard levels are provided below . The HCT908 tool is designed ONLY for cutting holes in steel and stainless steel pipe and This safety alert symbol indicates copper tubing, and should ONLY be used for important safety messages . - Page 5 TM-HCT908 / Operating and Maintenance Instructions Manual Disconnect the power cord from the CAUTION electrical source before servicing the tool. Only authorized personnel should perform maintenance on the tool . Always The HCT908 tool is designed ONLY for disconnect the power cord from the...
-
Page 6: Introduction
. Upon receipt of the tool, ensure that all necessary parts are included . If any parts are missing, contact Victaulic . NOTE: If the tool is rented, save the container for return shipment . REV_C... -
Page 7: Power Requirements
TM-HCT908 / Operating and Maintenance Instructions Manual POWER REQUIREMENTS NOTICE • The tool is equipped with a UL Listed DANGER three-conductor cord and a three-prong, grounding-type plug to fit the proper • To reduce the risk of grounding-type receptacle. The green (or... -
Page 8: Tool Nomenclature
TM-HCT908 / Operating and Maintenance Instructions Manual TOOL NOMENCLATURE NOTICE • Drawings and/or pictures in this manual may be exaggerated for clarity. • The tool, along with this operating and maintenance instructions manual, contains trademarks, copyrights, and/or patented features that are the exclusive property of Victaulic. -
Page 9: Installing The Hole Saw
TM-HCT908 / Operating and Maintenance Instructions Manual INSTALLING THE HOLE SAW TOOL SETUP WARNING • DO NOT connect the tool to the electrical source until instructed otherwise. Accidental startup of the tool could result in serious personal injury. NOTICE 1. Thread or push the locking ring of the arbor •... - Page 10 TM-HCT908 / Operating and Maintenance Instructions Manual 3. Raise the drill motor to its highest position by 6. Place the hole cutting tool onto the pipe/ rotating the feeder knob counterclockwise . tubing . Wrap the chain around the pipe/tubing and insert is loosely into the chain slot on the tool’s base .
-
Page 11: Tool Operation
TM-HCT908 / Operating and Maintenance Instructions Manual TOOL OPERATION WARNING Switch – shown in • NEVER use the HCT908 Hole Cutting forward Tool for applications where spark position hazards exist or where contact with water can occur. Trigger Failure to follow this instruction could result in serious personal injury. - Page 12 TM-HCT908 / Operating and Maintenance Instructions Manual WARNING • DO NOT touch coupons with bare hands. Coupons can be hot and edges will be sharp. Failure to follow this instruction could result in serious personal injury. 5. While continuing to support the tool, unhook the chain from the slot .
-
Page 13: Removing The Hole Saw
TM-HCT908 / Operating and Maintenance Instructions Manual REMOVING THE HOLE SAW WARNING • Before removing the hole saw from the arbor assembly, disconnect the power ⁄ " 16 mm cord from the electrical source. Failure to follow these instructions could PIPE/TUBING SURFACE PREPARATION result in serious personal injury. -
Page 14: Maintenance
INFORMATION When ordering parts, the following information 1. Lubricate the feeder rod with light-grade oil . is required for Victaulic to process the order and send the correct part(s) . Parts can be ordered by calling 1-800-PICK-VIC . Tool Model Number... -
Page 15: Accessories
TM-HCT908 / Operating and Maintenance Instructions Manual ACCESSORIES ARBOR ASSEMBLY FOR 1 3/16-INCH OR LARGER DIAMETER HOLE SAWS ARBOR ASSEMBLY FOR 1-INCH DIAMETER HOLE SAW 14 15 16 17 18 19 20 Item Item Part No. Qty. Description Part No. - Page 16 The pilot drill does not retain the The coupon-retaining drill bit is damaged. Replace the coupon-retaining drill bit. coupon. In the event of tool malfunction outside the scope of the troubleshooting section, contact Victaulic for assistance. UPDATED 03/2018 TM-HCT908 3022 REV C...
Need help?
Do you have a question about the TM-HCT908 and is the answer not in the manual?
Questions and answers