Advertisement
PRE-HEATING
We know most of our customers love a nice hot coffee so follow these tips; if you're in a hurry, skip to Brewing. These tips will add
approximately 10 – 15°C to the temperature of the coffee.
1
FILL
2
WARM
Fill 1/3 of the Cafetière with boiling
Leave Cafetière for 1 minute allowing the
water. Place the double filter back in the
stainless steel components to warm.
Cafetière ensuring the lid is positioned
correctly and gently plunge.
BREWING
Dualit cafetiere serves up to 8 cups. (1x cup is 100 -110ml)
MEASURE GROUND
ADD BOILED WATER
1
2
COFFEE
=
7g
1x
Place the Cafetière on a dry, heatproof,
Boil water. Slowly add a maximum of
non-slip surface. Measure 1x rounded
880ml boiling water and carefully stir
tablespoon or 7g of ground coffee
the brew.
per serving. Place up to 8x rounded
tablespoons of pre-ground coffee (suitable
for cafetières). We recommend using no
more than 60 grams.
TIP - Use setting 3 - 5 if grinding fresh
coffee beans in your Dualit Coffee Grinder.
PLUNGE
OPEN SPOUT
4
5
FILTER
After 4 minutes hold the Cafetière handle;
Turn the lid to the open position. Serve hot coffee. Do not over-tilt the
slowly and gently push down on the
plunger.
TIP - If the plunger gets too stiff to push,
lift plunger approximately 5cm and push
down again, this breaks up the coffee puck
built up under the filters.
3
POUR
After 1 minute empty the Cafetière.
TIP - Pre warm cups for a hotter coffee.
TIP - Use hot milk for a hotter coffee.
BREW
3
880ml
MAX
Allow coffee to settle for 20-30
seconds before gently positioning lid.
Ensure lid is positioned correctly. Before
plunging leave the coffee brewing for 4
minutes, for the optimum brew,
then plunge.
TIP - Ensure the lid is rotated around the
correct way to close the spout and keep
heat in.
Cafetière
ASSEMBLY & DISASSEMBLY
BEFORE DISASSEMBLING THE FILTER, ALLOW THE CAFETIÈRE TO COOL DOWN COMPLETELY.
1
DISASSEMBLE FILTER
Holding the plunger knob, unscrew the
lower filter by rotating anti-clockwise.
Slide the components off of the shaft.
CLEANING & CARE
BEFORE CLEANING, ALLOW THE CAFETIÈRE TO COOL DOWN COMPLETELY.
EMPTY
1
Empty the drained coffee grounds over a
bin with a spoon.
TROUBLESHOOTING
POSSIBLE CAUSE(S)
DOUBLE FILTER IS TOO STIFF TO PLUNGE
1. Coffee puck has built up under the filters.
2. Too much ground coffee placed in Cafetière.
3. Coffee grind is too fine.
4. Upper and lower filter mesh have been assembled in the wrong
filter assembly.
MY COFFEE IS COLD
1. Cafetière is cold.
2. Cups are cold.
3. Lid is open whilst brewing.
THERE ARE COFFEE GROUNDS IN MY CUP
.
1. Upper and lower filter mesh have been assembled incorrectly.
2. Damaged filter mesh.
2
DOUBLE FILTER
3
UPPER FILTER
Fine mesh
LOWER FILTER
coarse mesh
Ensure the upper filter is assembled
First, slide the upper filter assembly onto
using the fine mesh and lower filter is
the shaft. Then screw the lower filter
assembled with the coarse mesh.
clockwise until tight. (see Know your
Cafetière)
DO NOT OVER TIGHTEN.
RINSE
2
3
Rinse the Cafetière body and double filter
Ensure the double filter is disassembled. Place
under running water to remove any coffee
both double filter components and Cafetière
grounds.
body on the top rack of the dishwasher.
SOLUTION(S)
1. Lift plunger approximately 5cm and push down again, this
breaks up the coffee puck, or re-stir the brew.
2. Reduce the amount of ground coffee.
3. Use a coarser coffee grind.
4. Upper filter assembly must be assembled with fine mesh.
Lower filter assembly must be assembled with coarse mesh. See
Assembly instructions for details.
1. Pre-heat Cafetière.
2. Pre-heat cups.
3. Ensure lid is in the closed orientation position to keep heat in.
TIP: Use hot milk for an even hotter drink.
1. Check double filter assembly diagram.
2. To obtain new filter mesh contact Dualit customer helpline
on +44 (0) 1293 652 500 (09:00 to 17.00 Monday to Friday).
Alternatively, email Dualit at info@dualit.com or
visit www.dualit.com
ASSEMBLE FILTER
DISHWASHER
Advertisement
