Advertisement
Quick Links
Instruction Manual
Headset Functions
seconds to search for and nd other Blue
1. Power ON your headset:
tooth devices around you.
Press and Hold the Function for about 3 seconds until the blue
7. When Bluetooth devices are found, the phone will display NoiseHush
indicator ashes four times. After powering on, your headset
"NH26". Scroll to it and press OK to con rm ty want to pair with it.
should automatically connect to your last used phone if it is in
8. Enter the Passkey "0000" when your phone prompts you. The phone
operating range. If no paired phone is in range or no phone has
will now pair with the headset.
been paired, the "N500" will enter Standby mode.
9. If your Bluetooth phone menu supports it "set as authorized" or "add
2. Power OFF your headset:
to trusted devices"
Press and Hold the Function for about 3 seconds until the red
10. Again select the NoiseHush "NH26" to connect with it. OR, Press the
indicator ashes twice.
Function to connect with the phone.
3. To Answer or End a call:
11. If the pairing is not successful, the Headset will return to the standby
mode after a while, please repeat the pairing process to try the pairing
Press the Function once when there is an incoming call to Answer.
again.
Press the Function once again to end the call.
12. Refer to your phones User Manual for any additional steps
5. To Reject* a call:
Press and Hold the Function for about 2 seconds when there is an
incoming call.
6. To Redial* the last call:
Press and Hold the Volume Up Button for about 3 seconds and then
release.
Note: To conserve battery, NoiseHush "NH26" will automatically turn o
7. To activate Voice Dialing*:
if it's not paired with your phone.
while connected to your phone, Press the Function once. Voice
commands must have been previously recorded into your phone
Stereo Separation: 40dB
(see your phones user guide)
Frequency Response: 20Hz - 16Khz
8. To adjust the Volume:
Click the Volume Up or Volume Down Button during a call. Adjust
• Physical
to the desired level. The volume level you set to will be
Dimensions: 110x65.5x40 mm
remembered by the NoiseHush "N500" and used on the next call.
Weight: 191g
• Input Connection
* To use these functions, your phone/device must support the
Audio in: iPod 30PIN Connector
Bluetooth Handsfree Pro le.
Contact Us
For additional help or to purchase accessories such as AC / DC,
please visit us at www.noisehush.com
LED indicator chart
Power on
Blue indicator blinks 4 times
Power o
Red indicator blinks 4 times
Standby mode
Blue indicator blinks once every 2 seconds
Sni mode
Blue indicator rapidly blinks twice every 10 seconds
Pairing mode
Red & Blue indicators alternately blink
Active call
Blue indicator rapidly blinks 2 times every 8 seconds
Low battery
All Blue indicators will change to Red
Charging
Red indicator is continuously ON steady on
Charging complete
Red indicator turns OFF
Note: Sni mode means your headset has a connection with your phone but is conserving power,
and will wake up when any function is activated.
Before use, you must pair the
NoiseHush "N500" Bluetooth headset with your cell phone.
Pairing will create a stored connection in the headset and
your Bluetooth cell phone. Pairing has to be done only
once, when rst connecting to a phone.
Charging the Headset:
Before you start, charge your "N500" unit by plugging the
USB Charger into the USB port on your computer then plug
the other end into the headset. The Red LED indicator will
light up showing that the unit is being charged. When
charging is complete the Red LED indicators will turn o .
Pairing the Headset:
1. First turn the phone OFF and then back ON again to refresh its
memory.
2. Bring the mobile phone to about 30cm from NoiseHush "N500"
headset.
3. Find the Bluetooth menu in your mobile phone. Turn Bluetooth
ON. (Check your mobile phone user guide)
4. With the NoiseHush headset OFF, Press and Hold the function
button for about 6 seconds until the LED ashes blue to red.
5. Your headset is now ready to be discovered by your Bluetooth
mobile phone.
6. Perform a Bluetooth device discovery on your mobile phone to
add a new device. It takes a few seconds to search for and nd
other Bluetooth devices around you.
7. When Bluetooth devices are found, the phone will display
NoiseHush "N500". Scroll to it and press OK to on rm that you
want to pair with it.
Pairing the Headset
8. Enter the Passkey "0000" when your phone prompts you. The
First turn the phone OFF and then back ON again to refresh its
phone will now pair with the headset.
memory.
9. If your Bluetooth phone menu supports it "set as authorized" or
Bring the mobile phone to about 30cm from NoiseHush "NH26"
"add to trusted devices"
headset.
10. Again select the NoiseHush "N500" to connect with it. OR,
3. Find the Bluetooth menu in your mobile phone. Turn Bluetooth
Press the Function to connect with the phone.
ON. (Check your mobile phone user guide)
11. If the pairing is not successful, the Headset will return to the
4. With the NoiseHush headset OFF, Press and Hold the function
standby mode after a while, please repeat the pairing process to
button for about 6 seconds until the LED ashes blue to red.
try the pairing again.
5. Your headset is now ready to be discovered by your Bluetooth
12. Refer to your phones User Manual for any additional steps
mobile phone.
6. Perform a Bluetooth device discovery on your mobile phone to
add a new device. It takes a few
Note: To conserve battery, NoiseHush "N500" will automatically
turn o if it's not paired with your phone.
USB Charging port
Function Button
Advertisement
