Advertisement
LEARNING
LEARNING
Your One For All remote control can learn any function from any other working remote
TO DELETE A LEARNED FUNCTION, THE PROCEDURE IS:
control. This can be useful if you are missing one or more functions from your original
remote control and would like to add them to the Smart Control. You can learn onto any
1.
key except Magic, Devices or Activity.
You can also learn a complete device if you can't find a code.
2.
To learn, firstly make sure you have all your original remote controls to hand, and that they
have working batteries in. To learn functions, the original remote should be
approximately 3cm from the OFA remote, pointing towards it as shown below:
3.
4.
Press the key to delete twice – the LED will blink twice.
2 - 5 CM
Repeat the above procedure for each key you want to delete.
1.
Hold down MAGIC until the LED under the device blinks twice. The LED
ACTIVITIES
under the current mode will stay lit.
2.
Using the DEVICES key, make sure the LED for the device you want to learn
An Activity is a grouping of two or more devices into a single mode based upon what
functions on is lit.
you're doing while using your remote - for example TV and Set Top Box can be combined
together into a Watch TV mode. In this mode keys will control only the relevant device, so
3.
GUIDE
Press 975 – the LED will blink twice.
in this example the Volume keys would control the TV, but the channel keys would control
the Set Top Box.
4.
Press and release the key you want to learn a function onto (for example
The OFA Smart Control features 3 Activity Modes; Watch TV, Watch Movie and Listen To
the FAV key) – The Watch TV and Listen To Music LEDs will light up.
Music. Each of these modes has a choice of devices to combine.
These are:
5.
Press and release the key on the original remote.
WATCH TV
6.
The LED under the device will blink twice to indicate the key has been learned correctly.
Combination 1:
Combination 2:
7.
Repeat steps 4 and 5 for each key you want to learn – remember you can learn from multiple
Combination 3:
remotes, but only one function per key.
8.
WATCH MOVIE
When you have learned all the functions you require, press and hold the
MAGIC key until the LED blinks twice and turns off.
Combination 1:
Combination 2:
Combination 3:
Hints
Combination 4:
•
If the LEDs shows one long blink at step 6, the function was not learned correctly, please try again
from step 4.
•
If you find one or more keys don't work properly after set up, you can re-enter the learning mode
LISTEN TO MUSIC
at any time by repeating the procedure from step 1.
Combination 1:
Combination 2:
Combination 3:
ACTIVITIES
If you set up the default devices for any Activity on the remote (for example a TV and STB
for Watch TV) that Activity will be set up automatically on the remote. If you would like to
Hold down MAGIC until the LED under the device blinks twice.
change to a different combination, the procedure is as follows:
The LED under the current mode will stay lit.
1.
Hold down MAGIC until the LED under the device blinks twice.
Using the DEVICES key, make sure the LED for the device you want
The LED under the current mode will stay lit.
to delete functions from is lit.
2.
Use the ACTIVITY key to scroll through the Activities until the
Press 976 – the LED will blink twice.
one you want to set is flashing.
3.
Press the number of the combination you want to set – e.g 2
for TV + STB + AUD in Watch TV.
4.
The LED will blink twice and go out.
To access the Activities, simply press the ACTIVITY key to scroll through until the desired
one is lit. You can return to controlling by device by using the DEVICES key.
AV Shift
As the AV key is intended to select the input on your TV and most TVs use a menu to select
from a list of inputs, when the AV key is pressed in an Activity, the Menu Up, Down, Left,
Right and OK keys temporarily control the TV. If the OK key is pressed, or no key is pressed
for ten seconds, these keys will revert to controlling the relevant device for the Activity
(e.g. STB in Watch TV Mode).
Power Macro
If you hold down the Power key for 2 seconds in any Activity, the remote will send the
Power function for each device contained within that Activity. So for example, holding
TV + STB (Default)
Power in the default setting for Watch TV will turn both the TV and Set Top Box on or off.
TV + STB + AUD
TV + AUD
MACROS
TV + BLU (Default)
PROGRAM A MACRO
TV + BLU + AUD
TV + MEDIA
You can program any key on your OFA remote (except Magic and Devices) to send
TV + MEDIA + AUD
multiple commands on a single press –a Macro. This can be useful for controlling multiple
devices to put them in a certain state – for instance you could put your TV on HDMI 1
and press Play on the Blu-ray player to start watching a movie. A key programmed with a
Macro will send the same Macro regardless of the device mode, so it is best to select a key
TV + AUD + MEDIA (Default)
you don't use.
AUD + BLU
To program a macro, the procedure is as follows:
AUD only
1.
Hold down MAGIC until the LED under the device blinks twice.
The LED under the current mode will stay lit.
MACROS
VOLUME LOCK
2.
Press 995 – the LED will blink twice.
If you always use one device to control volume, for example your TV or an AV Receiver, you
can set up the Smart Control to always control that device, regardless of which device your
3.
Next select the key you want to program the Macro on.
remote is controlling.
To do this:
4.
Now use the DEVICES key to select the device you want the first
1.
function of the Macro to come from, for example TV.
Hold down MAGIC until the LED under the device blinks twice. The LED under the
current mode will stay lit.
5.
2.
Next, press the key you want to include in the Macro, for example
Press 993 – the LED will blink twice.
3.
the AV key.
Use the DEVICES key to select the Device you want to lock the Volume to.
4.
Press MAGIC once – the LED will blink twice and volume is now locked.
6.
Repeat steps 4 (if necessary), and 5 to add more keys to the Macro. You can include up
to 15 key presses.
To unlock the volume and set every device back to controlling its own volume, the
procedure is:
7.
To store the Macro, hold down the MAGIC key until the LED blinks
1.
twice.
Hold down MAGIC until the LED under the device blinks twice.
The LED under the current mode will stay lit.
2.
* Remember to press the keys in the same order you would using your original remotes – so if you pressed AV on the TV
Press 993 – the LED will blink twice.
remote and then Play on the Blu-ray remote to watch a movie, do it in the same order on the Smart Control.
3.
Press VOLUME UP – the LED will blink four times and Volume is now unlocked.
* If the LED shows a long blink when you press a key in steps 4 or 5, you have entered too many keys, please try again.
Please note that Volume Lock only applies in Device Mode – Activities are unaffected.
TO DELETE A MACRO
If you want to remove a macro from a key, please perform the following:
THE NETTV FEATURE
1.
Hold down MAGIC until the LED under the device blinks twice.
The LED under the current mode will stay lit.
The Smart Control features a "NETTV" key for viewing digital TV, streamed over the inter-
2.
Press 995 – the LED will blink twice.
net. If your original remote control already had a key for this - for example many newer TVs
have a Netflix key - then this key will perform exactly the same as the key on your original
3.
Press the key the macro is programmed on.
remote. However if you did not have a key like this, but still had the ability to watch a
streaming service, you can use this key as a shortcut by programming a macro on it. Most
4.
Now hold down the MAGIC key until the LED blinks twice –
AV devices which are connected to the internet, such as Smart TVs or streaming Set Top
the Macro is deleted.
Boxes have one or more applications they can run to access TV viewing via the internet.
Examples of these would be Netflix, YouTube, Amazon Prime, BBC iPlayer or similar.
MACROS ON ACTIVITIES
To program the macro, you first need to know the device you use to access the service,
Another handy feature of the Smart Control is to put Macros on Activities; you could for
and then the sequence of keys you need to press to always bring up the service you prefer,
example program the Watch TV Activity to send a Macro to turn on the TV and Set Top
For example, some Panasonic TVs will start Netflix by pressing the Apps key, then Menu
Box when selected. To do this, simply use the Activity key to select the Activity in step 3 of
Down Twice, and finally the OK key. Or on an Apple TV, the sequence is Menu, Menu Down
the procedure "Program a Macro". Next time you use the Activity, the Macro will be sent 3
and OK.
seconds after you select it using the Activity key.
Once you have determined the sequence for your device, follow these steps:
If you want to delete a Macro from the Activity, select it during step 3 of "To Delete a
1.
Macro".
Sit in front of your device with It switched on (not on standby)
2.
3.
THE NETTV FEATURE
4.
Now perform the sequence of keys exactly as would normally. The
remote will operate your device and the macro is recorded in real
time - so if it normally takes a few seconds for your device to react
don't worry.
5.
One you have finished the sequence - and the Streaming Service
has started on your device - hold down the NETTV key until the LED
blinks twice and goes out. The macro is now stored.
Tips
•
Make sure the Smart Control Is operating the device in question before programming
•
If you find the Macro doesn't work as expected, you can just repeat the same
sequence to reprogram
•
When programming, wait for your device to respond first, the remote will remember
the timing
•
The NETTV macro is tied to one device, remember to make sure you are watching the
correct device.
THE OFA APP
Your One For All Smart Control contains codes for all popular devices and brands, but new
codes are added to our online database every day. Using the One For All App on
your iPhone or Android phone will allow you to upgrade any new codes into your
remote using Bluetooth Smart, also known as Bluetooth Low Energy*. This will ensure that
the remote will never become obsolete. You can also use the app to set up all devices,
giving you the ability to enter the model numbers of your equipment to get the right code
first time. It can also help with selecting the right inputs for your Activities. *
* Dependent on device and commands available.
If you would like to download the app, follow the links below:
* Please ensure your phone is compatible with Bluetooth Smart. A list can be found by scanning the QR code above.
Universal Electronics, declares that this product is in compliance with the essential requirements and other relevant
Hold down the NETTV key until the LED blinks twice and stays lit
provisions of Directive 1999/5/EC.
A copy of the EC declaration of Conformity is available at
Use the DEVICES key to select the device you want to use for the
One For All is a registered trademark of Universal Electronics B.V.
NETTV macro (e.g. TV)
P.O. Box 3332, 7500 DH, Enschede, The Netherlands
www.ofa.com/smartcontrol
http://www.oneforall.com/DOC_URC7955
Advertisement
