Dickson FT620 Quick Start Manual

While battery operated:
If AC power is removed while the logger is on, a rechargeable battery will
•
provide backup for up to 20 hours.
The Logger will display "NO A/C" in the lower right corner of the display.
•
The display will remain on for 2 minutes and will then turn off to conserve
•
battery power.
To reactivate the display, press the On/Off button. The display will power
•
on, displaying the most recent data, for 2 minutes before turning the display
off. After 20 hours the logger must be powered via AC in order to turn on.
The logger will continue to log data while operating on battery only power
•
while the display is off, for up to 20 hours.
The logger will not sound an audible alarm when an alarm condition is
•
present while operating on battery power.
The unit must run for 24 hours before the backup battery is fully charged.
•
NOTE: The logger is set to wrap when full. Depend NOTE: The logger is set to wrap when full. Depend NOTE: The logger is set to wrap when full. Depend NOTE: The logger is set to wrap when full. Depending on the time graph
interval and the duration of lost AC, interval and the duration of lost AC, older data will be lost. interval and the duration of lost AC, interval and the duration of lost AC,
Wall Mounting Wall Mounting Wall Mounting Wall Mounting
Your Touchscreen includes a wall mount plate, two each: wall anchors, #4 screws.
Follow the steps below for proper placement:
Whenever possible, mount plate to studs using #4 screws (included).
•
If studs are not available:
•
Use a 5/32 drill bit to drill 2 pilot holes.
o
Gently tap wall anchors (included) into holes.
o
Secure plate to wall using #4 screws (included).
o
Warranty Warranty
Warranty Warranty
Dickson warrants this line of instruments will be free from defects in material and
workmanship under normal use and service for a period of twelve months, after
delivery. This warranty does not cover routine calibration or battery replacement.
For Specifications and Technical Support, go to
or contact us via telephone at 800.323.2448.
ing on the time graph ing on the time graph ing on the time graph
older data will be lost. older data will be lost. older data will be lost.
http://www.dicksondata.com http://www.dicksondata.com http://www.dicksondata.com http://www.dicksondata.com
R24 07022012 V3
DICKSON Touch DICKSON Touchs s s s creen Logger
DICKSON DICKSON Touch Touch
FT620/FT625/FT6 FT620/FT625/FT6 FT620/FT625/FT63 3 3 3 0 0 0 0 / / / / FT640 FT620/FT625/FT6
Getting Started Getting Started
Getting Started Getting Started
Your Color Touchscreen Logger includes the following Your Color Touchs Your Color Touchs Your Color Touchs creen Logger includes the following creen Logger includes the following creen Logger includes the following: : : :
AC Adapter
•
Probe or Pod
•
Certificate of Calibration
•
Quick Start Manual
•
* * * * SD SD Flash Memory Card Flash Memory Card, , , , USB Cable and DicksonWa USB Cable and DicksonWare re re re S S S S o o o o f f f f t t t t w w w w a a a a r r r r e e e e a a a a r r r r e e e e s s s s o o o o l l l l d d d d s s s s e e e e p p p p a a a a r r r r a a a a t t t t e e e e l l l l y y y y . . . .
SD SD Flash Memory Card Flash Memory Card USB Cable and DicksonWa USB Cable and DicksonWa
Presets Presets
Presets Presets
Model: FT FT FT FT6 6 6 6 20/FT 20/FT 20/FT6 6 6 6 25/FT 20/FT 25/FT6 6 6 6 30 25/FT 25/FT 30/FT 30 30
•
Time Scale: 1 Hour / Sample every 6 sec
Temperature Range: 0 to 100
Unit of Measure: Deg. F
Alarm: OFF
Quick Start Quick Start
Quick Start Quick Start
The Touch The Touchs s s s creen Logger is a computer The Touch The Touch creen Logger is a computer creen Logger is a computer device and must be set and restarted creen Logger is a computer
use. . . . use
use use
1) Plug the AC adapter into a standard electrical outlet, connect the logger to
the AC adapter and slide the power switch up to the "On" position.
2) Set Time: Press Menu Setup
3) Set Date: Press Menu Setup
4) Set Time Scale: Press Menu
5) Power off the logger, wait 10 seconds and power on the logger
6) Press Current to view current readings. The logger is ready for use when
readings are displayed. If no readings are displayed, repeat the above steps.
Logger Time: The logger does not automatically adjust for daylight savings. You Logger Time:
Logger Time: Logger Time:
must manually adjust the logger time during the start and end of Daylight Savings.
Exporting Data: Exporting Data: Saved data can be exported to and viewed in DicksonWare Exporting Data: Exporting Data:
The logger must be CLEARED via DicksonWare 17.12 or greater prior to
•
logging and downloading data.
Export data using the USB cable or Flash Memory Card. Open DicksonWare
•
to view exported data.
When running When running DicksonWare on a computer When running When running DicksonWare on a computer DicksonWare on a computer DicksonWare on a computer with Da
•
adjust adjust the computer adjust adjust the computer the computer the computer as follows: as follows: as follows: as follows:
From Time & Date Settings:
creen Logger
creen Logger creen Logger
FT640 FT640 FT640/ / / / FT6 FT645/ FT6 FT6 45/ 45/FT660 45/ FT660 FT660 FT660
/FT /FT6 6 6 6 40/FT /FT 40/FT 40/FT6 6 6 6 45 40/FT 45/FT 45 45 /FT /FT6 6 6 6 60 /FT 60 60 60
device and must be set and restarted p p p p r r r r i i i i o o o o r r r r t t t t o o o o device and must be set and restarted device and must be set and restarted
Set Time Save OK
Set Date Save OK
Set Scales Set Time Scales Save
with Da with Da with Day y y y l l l l i i i i g g g g h h h h t t t t S S S S a a a a v v v v i i i i n n n n g g g g s s s s s s s s e e e e t t t t t t t t i i i i n n n n g g g g s s s s , , , ,
OK