Advertisement
How you measure your blood sugar.
Time and date are preset, please check that this is correct the first time you use
the meter.
1. Wash hands with soap and water.
2. Take a new test strip from the bottle and replace the cap immediately.
3. Place the sole of the test strip that has a metallic contact surface, into
the meter opening.
4. The meter shows a blinking blood drop and is now ready for measurement.
5. Stick with the sampler.
6. Put the blood drop against the short side of the stick that absorbs the right
amount of blood. A beep sounds and countdown starts on the display.
7. Read the test results. A beep sounds (if enabled) when the result is
displayed on the screen.
8. Press the eject button to eject the used test strip. The meter turns off
automatically.
How to select a measured value.
1. When your test result appears, press
starts flashing. With the arrow keys (
2. Confirm your selection by pressing the
multiple selections (but only when you select the
repeat steps 1 and 2.
How to set the time and date.
1. Check that the meter is off. (If not, press
2. Press
3. Press
various menus.
4. Use
next step: year, month, day, time format, hour, minute.
5. After confirming the minutes (by pressing
the Setup menu.
How to manage the measurement results in memory.
Your meter stores up to 730 results with date, time and marks.
1. Make sure the meter is off. (If not, press
2. Press
3. The latest test results with the time, date and selections are shown.
4. Press
5. Press
View average results for the 1, 7, 14, 30, 60 or 90 days.
1. Press
is displayed on the screen). The meter shows the day's average.
2. Continue to press
90 days.
3. Press
Wireless transmission via NFC
Your saved test results can be transferred to an NFC-enabled device (such as
a smartphone) with an NFC-compatible application installed (eg GlucoLog).
The first time, you must turn on your meter NFC function (found in the
setup menus) by pressing the
Test Strip Port
confirm and leave.
1. Activate the NFC-transfer in the app in your smartphone.
2. Place your meter close to your smartphone (<1 cm).
3. The meter starts automatically and the data is transferred (
on the screen).
4. When the data transfer is completed, "End" appears on the screen
along with the symbol
5. Press the
How to replace the battery in GlucoMen
The meter is powered by two CR2032 3V batteries. When the symbol
battery is lit, it is time to change. You do not have to set the date and time if you
insert the new batteries within 2 minutes after the old is removed. How to use:
1. Make sure the meter is off.
2. Open the battery cover on the back of the meter and remove the batteries.
Buttons
Up/Down
3. Insert the new batteries in the battery holder with the "+"- side up.
4. Close the battery cover.
(before meal),
(after meal),
4 seconds to enter the setting menu.
or
to scroll the setup menus and press
or
to select the value. Press
for 2 seconds to start ("mem" appears on the screen).
or
to scroll to the memory.
for more than 3 seconds to turn off the meter.
for 2 seconds to turn on the meter. Press
to display the average for 1, 7, 14, 30, 60 or
for more than 3 seconds to turn off the meter.
or
to select ON or OFF . Press
, and a beep sounds.
button for 3 seconds to turn off the meter.
until the selection symbols
), select the desired mark
(training) or
(general).
button. You can select
or
),
for 3 seconds)
to access the
to confirm and go to the
) will return to
for 3 seconds).
again ("AVG"
(Near Field Communication)
to
flashes
Areo.
®
low
3.
The opening
of the test
Contact Area
6.
Test Strip Port
Button for
On/Off/Enter
Buttons
Up/Down
Eject button
Antenna (NFC)
Battery Cover
Data Transfer
Port
How to set the t
1. Check that the meter
2. Press
4 seconds
3. Press
or
to scrol
various menus.
4. Use
or
to select
next step: year, mont
5. After confirming the
the Setup menu.
How to manage t
Your meter stores up to
1. Make sure the meter
2. Press
for 2 second
3. The latest test results
4. Press
or
to scro
5. Press
for more th
View average results fo
1. Press
for 2 secon
is displayed on the sc
2. Continue to press
90 days.
3. Press
for more tha
Wireless transmiss
Your saved test results can
a smartphone) with an NFC
The first time, you must tu
setup menus) by pressing
confirm and leave.
1. Activate the NFC-transfe
2. Place your meter close t
3. The meter starts automa
on the screen).
4. When the data transfer i
along with the symbol
5. Press the
button for 3
How to replace th
The meter is powered by tw
battery is lit, it is time to cha
insert the new batteries with
1. Make sure the meter is o
2. Open the battery cover o
3. Insert the new batteries
4. Close the battery cover.
Advertisement
