Advertisement
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or un-
locked. If the learn routine has previously been locked, it must be unlocked
with Bitwriter® - this cannot be done manually with the Valet Switch.
The Bitwriter®
gives you access to a wider range of system options. These
features and the adjustments that may be programmed are described in the table
below. Default settings are in bold type.
Feature
Settings (Factory default in bold)
Siren Duration
1–180 seconds (30 seconds)
Auxiliary 1 Timed
1– 90 seconds (30 seconds)
Auxiliary 2 Timed
1– 90 seconds (30 seconds)
Auxiliary 3 Timed
1– 90 seconds (30 seconds)
Auxiliary 4 Timed
1– 90 seconds (30 seconds)
Zone 2 shock adjust
level 0 – 20 (Level 10)
Feature Menus
Default factory settings are in bold type.
Menu 1: Basic Features
Feature
1- chirp setting
2- chirp setting
#
1-1
Active arming
Passive arming
1-2
Chirps ON
Chirps OFF
1-3
Ignition controlled door lock
Ignition controlled door lock OFF
ON
1-4
Ignition controlled door unlock
Ignition controlled door unlock OFF
ON
1-5
Active locking
Passive locking
1-6
Panic w/ignition ON
No Panic w/ignition ON
1-7
0.8 second door lock pulses
3.5 second door lock pulses /
0.4 second door lock pulses
1-8
Forced passive arming ON
Forced passive arming OFF
1-9
Automatic Engine Disable ON
Automatic Engine Disable OFF
1-10
Vehicle Recovery System (VRS)
(VRS) OFF
ON
1-11
Code Hopping™ ON
Code Hopping OFF
Menu 2: Advanced Features
Feature
1- chirp setting
2- chirp setting
#
2-1
Multi-level Arming (progres-
(grouped/off)
sive)
2-2
30 second siren duration
60 second siren duration
2-3
NPC® ON
NPC OFF
2-4
Progressive door trigger
Instant door trigger
2-5
Valet switch input: 1 pulse
Valet switch input 2-5 pulses
2-6
Bypass Notification (On)
Bypass Notification (Off)
© 2013 Directed. All rights Reserved.
2-7
Enhanced domelight control
Door only/ignition only/Off)
(Full)
2-8
Single unlock pulse
Double unlock pulse
2-9
Single lock pulse
Double lock pulse
2-10
Comfort Closure (ON)
Comfort Closure (OFF)
2-11
Immobilizer Circuit (normally
Immobilizer Circuit (normally open)
closed)
2-12
Hood Trigger (normally closed)
Hood Trigger (normally open)
2-13
Dual Sensor Type (On)
Dual Sensor Type (Off)
2-14
High Security Disarm (On)
High Security Disarm (Off)
2-15
One Time Bypass (On)
One Time Bypass (Off)
Menu 3: Advanced Features
Feature
1- chirp setting
2- chirp setting
#
3-1
Horn (pulsed)
Horn (constant)
3-2
Horn Function (full alarm only)
Siren function _ chirp length
(20ms/30ms/40ms/50ms)
3-3
Factory Disarm with Trunk
Factory Disarm with Trunk Relase
Release (on)
(off)
3-4
Ground When Armed in Valet
Ground When Armed in Valet (Off)
(On)
3-5
Auxiliary 1 Validity
latched/latched, reset with igni-
tion/30 second/60 second/90
second timed/remote start report
3-6
Auxiliary 1 Linking (none)
Arm/Disarm/both
3-7
Auxiliary 2 Validity
latched/latched, reset with igni-
tion/30 second/60 second/90
second timed
3-8
Auxiliary 2 Linking (none)
Arm/Disarm/both
3-9
Auxiliary 3 Validity
latched/latched, reset with igni-
tion/30 second/60 second/90
second timed
3-10
Auxiliary 3 Linking (none)
Arm/Disarm/both
3-11
Auxiliary 4 Validity
latched/latched, reset with igni-
tion/30 second/60 second/90
second timed
3-12
Auxiliary 4 Linking (none)
Arm/Disarm/both
3-13
Parking Light Supervision (On)
Parking Light Supervision (Off)
3-14
Ignition Controlled 2nd Unlock
Ignition Controlled 2nd Unlock (im-
(progressive)
mediate - with first unlock)
Transmitter learn routine
1.
Open a door.
2.
Turn the ignition on.
3.
Select a channel. Press and release the Valet switch the number of times neces-
sary to access the channel desired (see programming menu), and then press
and hold the Valet switch once more. The siren chirps and the LED blinks the
number of times corresponding to the channel number chosen.
4.
Continue holding the Valet switch.
5.
While holding the Valet switch, press the button on the remote control you
want to assign to the selected channel (for autolearn or to delete all transmit-
ters/remote controls, press the
button). The siren chirps indicating success-
AUX
ful programming.
6.
Release the Valet switch to exit the learn routine. The siren sounds one long
chirp indicating exit.
The learn routine exits if any of the following occurs:
•
The ignition is turned off
•
The door is closed
•
There is no activity for 15 seconds or more
•
The Valet switch is pressed too many times
Channel #
Function
Wire Color
1
Auto/Learn Standard*
2
Lock/Arm/Panic On/Panic Off
3
Unlock/Disarm/Panic Off
4
Trunk Release
Red/White
5
Auxiliary 1
White/Blue
6
Auxiliary 2
Violet/Black
7
Auxiliary 3
White/Black
8
Auxiliary 4
Gray/Black
9
Arm/Disarm/Panic
10
Panic Only
11
Delete All Transmitters/Remote Controls**
*
See owner's guide for transmitter configuration.
** The delete all transmitters option also resets the programmed settings to their
default factory state.
Shock Sensor Adjustment
Note: This procedure applies only to the onboard Zone 2 shock sensor.
To enter shock sensor adjustment mode:
IMPORTANT! The system must be disarmed, and doors and other protected points of entry (zones 1 and 6)
must be closed, and the ignition (zone 5) must be off.
Press and hold AUX and
buttons for 4 seconds. This siren emits one long chirp
to indicate entry into mode. The LED illuminates and remains on for the duration of
AUX
the adjustment.
Note: When the shock sensor adjustment mode is entered, all other timers and
operations are bypassed until adjustment mode is exited.
To adjust the shock sensor setting:
Note: When adjusting the shock sensor, ensure that the vehicle's doors are closed.
Increase Sensitivity—Press and release the
button to increase shock sensor
sensitivity by one step. The siren chirps twice times for each incremental step. When
AUX
maximum sensitivity is reached, the siren emits two short chirps and then one long
chirp.
Decrease Sensitivity—Press and release the
button to decrease shock sensor
sensitivity by one step. The siren chirps once for each decremented step. When
AUX
minimum sensitivity is reached (sensor is Off), the siren emits one short chirp and
then one long chirp.
Testing Sensor—Carefully impact the door pillar of the car after any sensitivity in-
crease or decrease adjustment. The siren chirps once if the impact was great enough
to generate a full trigger. Pre-warn level is set automatically. When the desired setting
is reached, sensor adjustment mode can be exited.
The adjustment mode will be exited if:
•
No input from transmitter for 15-seconds.
•
No input from sensitivity testing for 15-seconds.
•
The ignition is turned On.
•
The Valet switch is pressed.
The siren emits one long chirp and the LED turns off when this mode is exited.
Reset Shock Sensor to Default Setting
The shock sensor can be restored to a default setting of 10 to facilitate re-adjustment
at any time while in adjustment mode.
1.
Simultaneously press the AUX and
buttons.
2.
The system emits three chirps to indicate the sensor has been reset to level 10.
AUX
3.
The system returns to shock sensor adjustment mode for further adjustment, if
required.
Long Term Event History
The system stores the last six full triggers in memory. These are not erasable. Each
time the unit sees a full trigger, the older of the two triggers in memory is replaced by
the new trigger. To access long term event history:
1.
With the ignition Off, press and hold the Valet switch.
2.
Turn the ignition On.
3.
Release the Valet switch.
4.
Within 5 seconds, press and release the Valet switch. The status LED flashes in
groups indicating the last six zones that triggered the unit for 1 minute or until
the ignition is turned off. Refer to table of zones.
Table of Zones
Zone
Trigger Type Description
Input Description
1
Instant
Optional trunk input, 12 pin Blue wire
2
Multiplexed
Onboard shock sensor
3
Instant two-stage, or constant
Door switch circuit, 12 pin Green or
Violet wire
4
Multiplexed input (sensors)
Optional Sensor (Sensor 2)
5
Two-stage (similar to doors)
Ignition input, 12 pin Yellow wire
6
Hood trigger
Optional hood input, 8 pin Grey wire
7
Multiplexed input (sensors)
Optional Sensor (Sensor 3)
Note: The Warn Away response does not report on the LED.
Guide Translations
For a Spanish or French version of the Installation Guide, please download it
from www.directechs.com under "Resources".
Traducción de los manuales:
Para obtener una versión en Español o Francés del Manual de Instalación,
descárguela de www.directechs.com bajo el título "Recursos" ("Resources").
Traduction du guide:
Pour une version française ou espagnole du guide d'installation, veuillez le
télécharger à www.directechs.com sous «Resources».
More information and full Installa-
tion Guide can be found online at:
www.directechs.com
QRN3102 2013-01
2
Advertisement
