D2D 3102 Quick Reference Install Manual

Quick Reference Install Guide
Vehicle Security System
Model 3102
Wiring Connections
Domelight Supervision
Output (pin #87 of onboard
relay): Connect to (-) ground
if the domelight circuit is
negative or to +12V if the
Trunk Release Output: Connect to the
domelight circuit is positive.
vehicle negative (-) trunk release relay or
other low current device. NEVER connect
directly to a motor or high current device
without a relay.
12V Constant Power Input: Remove the
inline fuse before connecting to a wire
that has (+) 12V at all times. Reinstall the
inline fuse when wiring connections are
complete.
Siren Output: Connect to the (+) wire on
the siren.
+12V Ignition Input: Connect to a wire
that has (+) 12V while the key is in the
run and crank positions.
Chassis Ground Input: Connect to a
scraped (bare) metal surface in the driver
kick panel. NEVER connect to dash
brackets or to a factory ground.
Door Trigger Input:
Green: Connect to a wire that rests at (+)
12V when all doors are closed and (-)
ground when any door is opened.
OR
Violet: Connect to a wire that rests at
ground when all doors are closed and
(+) 12V when any door is opened.
Instant Trigger Input: Connect to a wire
in the vehicle that goes to ground when
opened (typically the trunk) or to an op-
tional Directed single zone sensor.
Domelight Supervision Output (pin #30
of onboard relay): Connect to a wire that
turns on the domelight to illuminate the
vehicle interior when disarming and turn-
ing off the ignition
Aux 1 Output: Connect to an auxiliary
convenience or expansion option. NEV-
ER connect directly to a motor or high cur-
rent device without a relay.
(+ or -) Light Flash Output: Connect to
the vehicle parking light wire. Select the
correct polarity with the output or vehicle
damage may occur.
(87A) Normally Closed: To car side of
starter wire if programmed as a Nor-
Ground When Armed Output: Connect
mally Closed circuit (factory default).
to a starter interrupt relay or an accessory
that requires a ground to activate when
(87) Normally Open: To car side of
the system is armed.
starter wire if programmed as a Nor-
mally Open circuit.
Important: NEVER connect 200mA low current outputs
(30) Common: To key side of starter
directly to a motor or high current device WITHOUT
wire.
a relay,
© 2013 Directed. All rights Reserved.
Bitwriters with a date code of 6a or older require an IC
upgrade (p/n 998M). Some bitwriters with a date code
of 6B do not require the IC upgrade, refer to tech tip #
1112 for more information.
Pin #87A of Onboard Pin #30 of Onboard
Door Lock Relay: Door Lock Relay:
This wire is typically Connect to the door
used whenever the door lock wire in the vehicle.
lock switch needs isola-
tion.
Note: For more door lock wiring information, see tech tip #1041 at: www.directechs.com (authorized users only).
Valet Switch
Sensor 2
Note: The sensor ground outputs from the system
are only active when the system is armed.
Sensor 3
Violet (87) of onboard Unlock Relay
Blue/Black (30) of onboard Unlock Relay
Brown/Black (87A) of onboard Unlock Relay
Violet/Black (87) of onboard Lock Relay
Green/Black (30) of onboard Lock Relay
White/Black (87A) of onboard Lock Relay
Black/White (87) of onboard Domelight Sprvsn Relay
Red/White (-) 200mA Trunk Release Output
Red (+) 12V Constant Power Input
Brown (+) Siren Output
Yellow (+) Switched Ignition Input
Black (-) Chassis Ground Input
Violet (+) Door Trigger Input
Blue (-) Instant Trigger Input
Green (-) Door Trigger Input
Black/White (30) of onboard Domelight Sprvsn Relay
White/Blue (-) 200mA Aux 1 Output
White (+ or -) Selectable Light Flash Output
Orange (-) 500mA GWA Output
Green/Black
Green
Green/White
The Bitwriter® (p/n 998U)
requires chip version 2.4 or
newer to program this unit.
Pin #87 of Onboard Pin #87A of Onboard Pin #30 of Onboard
Door Lock Relay: Door Unlock Relay: Door Unlock Relay:
Connect to (-) ground if This wire is typically Connect to the door un-
the locks are negative used whenever the door lock wire in the vehicle.
or to +12V if the locks lock switch needs isola-
are positive. tion.
998T Bitwriter
/SmartStart
Antenna
Detail
Parking Light
Flash Jumper
(-) 200mA OEM Alarm
Disarm Output
Lt. Green/Black
Lt. Brown (-) 200mA Horn Honk Output
Violet/Black (-) 200mA Aux 2 Output
White/Black (-) 200mA Aux 3 Output
Gray/Black (-) 200mA Aux 4 Output
Orange/Black (-) 200mA Retained Acc Output
Gray (-) Hood Trigger Input
Lt. Blue (-) 200mA 2nd Unlock Output
LED
Remote control configuration
4- button remote control configuration
Feature Description
Arm: Lock the doors and arm the vehicle
Disarm: Unlock the doors and disarm the vehicle
Pin #87 of Onboard
Trunk Release/Silent Mode: Activate Silent Mode
AUX
AUX
Door Unlock Relay:
and Auxiliary functions
Connect to (-) ground if
Panic
A U X
the locks are negative
A U X
or to +12V if the locks
are positive.
Aux 1: Press together to control an Auxiliary output
and
Programming System Features
The System Features Learn Routine dictates how the unit operates. It is possible to
A U X
access and change most of the feature settings using the Valet switch.
A U X
1. Open a door.
2. Turn the ignition on, then off.
3. Select a Menu. Press and hold the Valet switch. The number of siren chirps
indicates the menu number. 1 chirp indicates menu 1, 2 chirps - menu 2, and
3 chirps for menu 3.
4. When the desired menu chirps are heard, release the Valet switch.
5. Select a Feature. Press and release the Valet switch the number of times cor-
responding to the feature you wish to change. Then press and hold one more
time to select the features.
Program the Feature. While holding the Valet switch, you can program the
6.
feature using the remote control.
To change the desired options press;
three or higher chirps setting.
Once a feature is programmed:
OEM Alarm Disarm: Connect to the
• Other features can be programmed within the same menu
factory alarm disarm wire in the ve-
• Another menu can be selected
hicle (if applicable). NEVER connect
• The learn routine can be exited if programming is complete
directly to a motor or high current de-
vice without a relay.
To access another feature in the same menu:
Press and release the Valet switch the number of times necessary to advance
1.
Horn Output: Connect to the vehicles
from the feature you just programmed to the next one you want to program.
(-) horn honk relay wire.
2. Then press the Valet switch once more and hold it.
Aux 2 Output: Connect to an auxilia-
ry convenience or expansion option.
To select another menu:
NEVER connect directly to a motor or
1. Press and hold the Valet switch.
high current device without a relay.
2. After 3 seconds, the unit advances to the next menu and the siren chirps, indi-
Aux 3 Output: Connect to an auxilia- cating which menu has been accessed.
ry convenience or expansion option.
NEVER connect directly to a motor or The learn routine exits if any of the following occurs:
• The open door is closed
high current device without a relay.
• The ignition is turned On
Aux 4 Output: Connect to an auxilia-
• There is no activity for 15 seconds or more
ry convenience or expansion option.
• The Valet switch is pressed too many times
NEVER connect directly to a motor or
high current device without a relay.
Programming continued on page 2.
Retained Acc Output: Connect to a
relay that controls the accessory cir-
cuit in the vehicle.
Hood Trigger Input: Connect to a
wire that goes to ground when the
hood is opened.
2nd Unlock Output: Connect to a
wire (or relay assembly) that unlocks
all doors when installing two stage
door unlocking.
= one chirp setting, while = two,
AUX AUX
1